Question about Hardware & Accessories
I just followed the directions from another fixya expert to try and correct and E2. The stove runs or a few minutes and then you get a strong kerosene smell and it ends up flashing E2. I've tried cleaning the white wire, red wire and gold nut. I unscrewed them all and tried to get the soot out but I still have an E2.
I am not a heating expert so take this with a grain of salt.
IMHO, a sooty burning oil burner (which kerosene is used in) is due to too much fuel or too little air. An oil burner consumes oxygen, therefore ventilation is required. A direct vent supplies makeup air and provides and exhaust path. Kerosene comes in a couple of different grades. K2 is generally used for heating.
SO, insure you have the correct type kerosene. Inspect your direct vent to insure it is drawing in air from the outside easily. Insure your control is not supplying too much kerosene.
The flame should not be red - that is a definite indication of too little air/too much fuel. If it is very blue, it may get blown out. Your manual should show you the perfect flame color.
If you are smelling kerosene, that would be a good indicator that something is wrong with your direct vent. Any leak between the exhaust section and the makeup air section will cause this. Reinstall the vent and insure the directions are followed. Moving the vent after installation is perfect for breaking the seals and creating the problem. Have you had any earthquakes lately?
Posted on Oct 04, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Toyostove Laser 73 EE2
The firing sequence for a L73 is blink, blink, blink, on the green burner light, then it clicks up to the medium, amber or yellow light...that's when the pump kicks on. If you hear click, click, click, or thump, thump, thump, that means the pump is starving for fuel. The problem is from the carburaot/sump back to the fuel tank. You may have icing in your line or a line restriction, no fuel, plugged fuel filter or plugged sump screen. You can thaw your fuel line, until you have a free flow of fuel and then push the red restart button on top of the sump. Try to restart your Toyo.
If you follow the firing sequence and hear no click, click, click or thump , thump, thump and your Toyo goes off on EE2 then you can have a dirty flame sensor...the whilte wire running to a U shaped part that is the ground for the entire unit. You can take ythe ytwo phillips screws out, turn the part to the side and wiggle it out. Clean it qith a green scrubby or sandpaper and put it back in. Be sure it points stright down. Then take out the igniter which are the red wires. Put a long screw driver in there and rattle it around real good. You are trying to shake any carbon cxhains off the burner ring that can be "shorting" the flame sensor. You can also removee the 1/2 inch flare nut from the fuel nozzle...brass yellow colored metal part, and put a paper clip or wire down that about 3 inches. That will clear any blockage in front or inside it. Put everything back together, hit the red reset button on the sump and re-fire your Toyo. You might get it going in this manner. If not, you may need a tuneup because your Toyo is too sooted up to run correctly. Try these things and post back!
Posted on Nov 14, 2008
SOURCE: Toyostove L-73
#1 and #2 are not the same at all. Toyo Laser 73 heaters should only use #1 home heating fuel or Water Clear Kerosene. If you burn #2 in your Laser 73 it will soot up in less than a week. It is a disaster, do not do it!!!
The difference between the fuels is the amount of carbon in them. # 2 has a lot of carbon and therefore more BTU's of heat per pound than # 1. All that carbon will end up on the burner, blower and in the heat exchanger. It will be the dirtiest job you have ever done.
Posted on Jan 07, 2009
If the dog Just chewed the wires you can splice them back together
But if you need a new one I can Mail you one.
Posted on Dec 13, 2009
SOURCE: getting code EE 2 on a laser 73
EE 2 usually has to do with the fuel. Does the heater make a loud ticking or thumping sound? That's the sound the fuel pump makes when its not getting any fuel. Check your filter, check the strainer in the fuel sump. Depending on how cold it is any water in the fuel line could be frozen blocking the fuel flow. You might also check the flame rod for soot. It can be cleaned with some steel wool.(email@example.com)
Posted on Jan 25, 2010
Testimonial: "by the time that this information was available the problem was solve.dirty injector and flame sensor"
Tips for a great answer:
Jul 01, 2011 | Rinnai Toyostove Direct Vent Heater:...
Jun 09, 2011 | Rinnai Toyostove Direct Vent Heater:...
Sep 18, 2010 | Rinnai Toyostove Direct Vent Heater:...
Jan 12, 2010 | Rinnai Toyostove Direct Vent Heater:...
Dec 12, 2009 | Rinnai Toyostove Direct Vent Heater:...
Oct 14, 2008 | Rinnai Toyostove Direct Vent Heater:...
Jan 06, 2008 | Rinnai Toyostove Direct Vent Heater:...
33 people viewed this question
Usually answered in minutes!