Question about Ibanez Music

1 Answer

What type of input Jack do I need for a ibanez guitar amp tbx30r?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 80 Answers

I believe you need a 1/4" unbalance plug for the amps input. Basically a guitar cord. If I am understanding the question. ? or if you want to know the actual "input jack",Maybe it is lacking or missing? than that would be a "1/4" unbalanced input jack". good luck, I hope this helps.

Posted on Aug 26, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
CRTN
  • 716 Answers

SOURCE: Line 6 Spider 2x12 100w combo - Input jack issue

Its a 1/4" mono Panel-Mount Audio Jack
and can be bought at
Radio Shack, Best Buy, Any Music Store
Click Here

Average price about $3.00

Posted on Mar 10, 2009

  • 1140 Answers

SOURCE: cable broke off in the input jack

I'm pretty sure t6hat the output jack is a sealed unit(contacts inside soldered to the surface of the circuit board. You may be able to grasp the center shaft of the plug with a thin jawed hemostat or really skinny long nosed pliers and pull it out that way. Make sure the amp is off and unplugged from the wall. If that doesn't work you will either have to get it removed at a shop or disassemble the amp to remove the circuit board and unsolder the jack and replace it or get the broken plug out of the jack once it is unsoldered. I've never had a Line6 apart yet but thats probably the type of jack they used. Thats because it has to be electronically isolated from the chassis. Hope this helps.

Posted on May 15, 2009

  • 5603 Answers

SOURCE: Peavey 115 Low hum Low volume from input

The preamp section has a problem. It could be anything in the preamp but is OFTEN the input jack itself. They take a lot of abuse.

Also the insert jack contacts that forward the preamp to the power amp if no external FX are used can go bad.

Additional things are circuit board cracks caused by rough handling and also controls that have had the knobs mashed in which can destroy the potentiometers they are connected to.

Posted on Sep 22, 2009

PolyrhythmFX
  • 109 Answers

SOURCE: sound is breaking up

Try another cable. If the cable is not the issue start inspecting the guitar's wiring. A bad solder joint or broken wire can cause problems. But I suspect the cable. An easy test if you don't have another instrument cable to try, use a multimeter and test both the tip and sleeve of the cable. You should have continuity on the tips of each end. And the sleeve should have continuity on both ends.

Posted on Mar 08, 2010

  • 1140 Answers

SOURCE: i need wiring diagram for ibanez gsr200 bass

Here is a diagram:http://forum.ibanez.com/default.aspx?g=posts&t=78892

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jack female connector type


switchcraft

your standard 1/4 in mono female jack.

Mar 18, 2014 | Ibanez RGD Series - RGD321 Electric Guitar...

1 Answer

Input jack


any input jack should work!

May 15, 2013 | Ibanez Tone Blaster TBX30R Guitar...

1 Answer

There's no sound when I put a cable in input, but when I put headphones too, there is a sound. How to reset ibanez mimx65?


If the sound you when plugging in the headphones is coming from the main speaker, it is just the interupt contacts on the headphones are making or breaking contacts. This can be a good sign if there is volume to it.

Make sure the plugs you are using are the right length for jacks in the Ibanez as there are 5 lengths in use.. If this just developed, the length issue is not a concern. If the jacks are loose, snug them down, it may be a faulty ground relying on the chassis contact with the jack.. It may be a broken wire. It can also be a dirty switch contact or dirty level control, especially the standby switch. make sure they are clean with some contact cleaner. Make sure your level is turned up too,

If you have effects, or a preamp on the guitar, make sure they have fresh batteries or good power connections and are not on mute.

Apr 11, 2012 | Ibanez MIMX65 Modeling Guitar Combo...

1 Answer

I have purchased 2 Ibanez TS8DX Tube screamers. Both are broken right out of the box. I plugged a cable into the out jack and into my amp. I then pluggen my guitar cable into the IN jack. Pushed the pedal,...


The input cable MUST be a TS (unbalanced cable) to turn the unit on. The sleeve of the input cable is what connects the battery. If you use a TRS cable at the input it likely will not turn on. A TRS cable has a tip, ring AND sleeve like many 1/4 inch stereo cables.

Sep 15, 2011 | Ibanez Ts9dx Turbo Tube Screamer Overdrive...

1 Answer

My acoustic electric guitar is giving intermittent sound any idea how to fix this problem


A common problem is a WORN jack that is caused by the user NOT looping the guitar cable through the strap or their belt loop. The rotation of the cable as it is played wears both the plug and the jack and causes noise and dropouts. Also verify that the battery connections are corrosion free. Also verify the problem is not with your amp.

Sep 09, 2011 | Ibanez Ael20e AcousticElectric Guitar with...

1 Answer

Well, my Ibanez TBX150R Tone Blaster Xtreme Guitar Combo Amp worked fine for the longest time, and suddenly after a show, every time I turned it on the "hot" channel it popped and banged every...


Sounds like a problem with the channel itself, if the clean channel works then its not the lead, input, guitar or the drivers. You have to be careful when opening up amps as some can hold a residual charge and there can be danger of electrocution.

I would recommend getting it looked at by a pro, it doesn't sound like an expensive fix.

Jun 30, 2011 | Ibanez Tbx150h Tone Blaster Xtreme Guitar...

1 Answer

I have a Ibanez TBX150H head, when I turn it on all I get is a buzzing noise coming through the speakers. Nothing drastic happened to it, just one day it wouldn't play.


Most common cause would be failed filter capacitor(s). Broken grounds neaar the input connector are another common problem. This will take electronic troubleshooting skills.

Mar 11, 2011 | Ibanez Tbx150h Tone Blaster Xtreme Guitar...

5 Answers

How do i plug my eletric guitar into an amp


Connect a 1/4" instrument cable from the guitar's 1/4" jack to the amp's 1/4" input.

Oct 02, 2009 | Dean Guitars Dean Ml79 Electric Guitar

1 Answer

Input wires broken loose, not sure where the go to


The center pin is your tip..which should have a wire going from 1/4" jack to the XLR jack. Pin 1 is earth ground...should be coming from 1/4" jack sleeve. Pin 3 would come from the 1/4" jack ring.
http://upload.wikimedia.org/wikipedia/commons/thumb/8/81/XLR_pinouts.svg/540px-XLR_pinouts.svg.png

If you are still having trouble, post links to pictures of the internals of the guitar showing the assembly.

Mar 27, 2009 | Music

Not finding what you are looking for?
Music Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ibanez Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

PickyPrick

Level 2 Expert

52 Answers

parsos215

Level 1 Expert

29 Answers

Are you an Ibanez Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...