Good morning, my Konica Minolta 190f says:please call service 001,what will I do to resolve this

Please refer to the service manuals and this.

Replacing a Drum Unit

Konica Minolta Manuals

https://manuals.konicaminolta.eu > contents











After Drum Unit replacement step 1 has been completed, check that the red-circled lock is located at the position indicated by a dashed line, then execute step ...

Konica Minolta REGIUS 190 Service Manual

ManualsLib

https://www.manualslib.com > ... > REGIUS 190











View and Download Konica Minolta REGIUS 190 service manual online. REGIUS 190 medical equipment pdf manual download. Also for: Dd-941.

Konica Minolta - Regius 190 Community, Manuals and ...

MedWrench

https://www.medwrench.com > equipment > konica-m...











Konica Minolta - Regius 190 by Konica Minolta. Konica Minolta - Regius 190. Forums ... Regius 190 Service Manual. SERVICE COMPANIESView All Computed Radiography ...

Konica Minolta Regius 190 (DD 941) Service Manual

Internet Archive

https://archive.org > details > manual_Konica_Minolta...











May 20, 2020 - KONICA MINOLTA. DIRECT DIGITIZER. REGIUS MODEL 190. (DD-941). SERVICE MANUAL. KONICA MINOLTA MEDICAL & GRAPHIC, INC.



..https://www.youtube.com/watch?v=lqfANSFl6Io

• As the title says, we have a 190F which shows out of toner. Have replace toner cartridge (often), main board and both sensors that detect toner in the cartridge, has anyone else had this on this lovely machine!

• Every new toner contains a little fuse (it is under two tiny contacts). When the user put the new toner into the printer, the fuse blows and the printer detects in this way that it has a new toner in; so if the toner has been for any reason only a moment into the printer cannot reset the message of add new toner.
• You can test the continuity between the contacts.

Solution A: put in a brand new toner and use the other(s) first of the natural end (so the message is not yet displayed)
Solution B: find a pico fuse of the same value and put it place. (if you are a tech you know the value, it the same in fuser or TBU ). Aldo

Turn off the machine, remove the toner bottle, then power on with the bottle out let the machine do its start up procedure. one it asks for the toner bottle install it correctly

Typically you would need to replace the fuser. I would recommend finding a service manual for removal and installation instructions.

https://www.biz.konicaminolta.com/download/users-guide/c1100_c1085/contents/id12-_101518117.html

https://www.scribd.com/doc/96776323/Top-10-Solutions-KONICA-MINOLTA

Why? It does that to produce nice copies and prints. Is it a constant calibration?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Something to do with main motor. paper jam. Or bad main motor.

Sir/Mam,
Power off the machine. Then remove the toner bottle, be careful the hole might be on the bottom and the toner is going to go everywhere. Then close the toner cover and turn on the machine. Let the machine go through it normal routine. When it asks for toner install the toner bottle correctly. If THE KNUB on the side of the bottle is damage put a new one in. That KNUB is what the toner motor uses to turn the bottle, if it damaged you get a code. If that does not work, you might have a bad motor or the home sensor or actuator for the toner bottle is bad worse case the control board is bad.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

I believe that error means the toner cartridges aren't installed like they should be. Re-install each toner and restart the printer.

Self Help Product Support Konica Minolta Business Solutions Inc
try this site

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f