Tip & How-To about Razor 300001-SL Ground Force Go Kart

Gas Engine Conversion

Just converted our Razor Kart to a 49cc gas motor. Is twice as fast as the electric version but was very unstable with the stock wheels. I went with 4" slicks and is much better. Transplanted the drive train from a pocket bike with electric start and speedometer. Was a 2 day project and was well worth the time.

Posted by on

Razor 300001-SL Ground Force Go Kart Logo

Related Topics:

Related Questions:

0helpful
1answer

razor ground force go cart
I don't think this would be a problem, as long as the wheels fit the axle properly, both in diameter, and length of shaft.
Read full answer
Aug 24, 2014 • Razor 300001-SL Ground Force Go Kart
0helpful
1answer

Duromax next generation xp10000E idle surging problems
I have a duromax 16hp engine on a murry go kart ran perfectly fine we took engine off kart painted kart put motor back on go kart now wont idle unless holding choke halfway open and new gas we drained gas before we started work on kart plesas help only about 10 hrs
Read full answer
Dec 26, 2012 • DuroMax XP10000E 4-Cycle Gas Powered...
0helpful
1answer

I have a ct-811b9 controller with my electric scooter and i un-hooked a connection and the controller almost littereally exploded and now the throttle does not work. i bought a new controller and now the throttle will not work. any help?
  • Replacement 24V controller with 4 pin throttle connector
  • For Razor E100(Versions 10+), E125 (Versions 10+), E150 (version 1+) and E175 (version 18+) eSpark(version 41+), Trikke E2(versions 1+) electric scooters.
  • Replace Razor part #: W13111612164 Model No: ZK2400-DP-LD-ROHS7, ZK2400-DP-FS-ROHS7
  • The E100 series Razor scooter is a PUSH START scooter. You need to push the scooter, twist the throttle and then the motor will engage
  • 1-Year Warranty - Money-back satisfaction guarantee
7 connectors, 5 plastic connectors & 2 metal connectors
Read full answer
Aug 01, 2011 • Electric 24v Controller Ct-811b9 For ...
0helpful
1answer

When I turn the switch on after charge, it blinks on and off and my son can not use the gas feed on the steering wheel. The power switch blinks on and off.
hi, a blinking red light ,is telling you that a battery is going bad or you have a bad plug , or your charger is going bad .
I had a razor scooter that had the blinking red light, it was a busted plug on the scooter where it plugs in.I had one scooter that had the blinking red light, it was A battery gone bad .
good luck!
Read full answer
Jan 29, 2011 • Razor 300001-SL Ground Force Go Kart
0helpful
4answers

Razor Ground Force Go Kart will not work.
replace thumb tab throttle. part is $12.99 from razor. go to razor site to order. i had the same problem after my daughter drove it over a bumpy sidewalk.
Read full answer
Mar 05, 2009 • Razor 300001-SL Ground Force Go Kart
Not finding what you are looking for?

4,097 views

Ask a Question

Usually answered in minutes!

Popular Questions

My charger light shows always green and it does not charge the scooter.

Razor E100 Electric Scooter

On an E 100 Razor scooter, the battery charger shows charged

Razor E100 Electric Scooter

Razor Ground Force Go Kart will not work.

Razor 300001-SL Ground Force Go Kart

Can't fold down a razor cruiser for storage, how do you do it?

Razor Scooters Cruiser Scooter

Clicking noise only and scooter wont run

Razor E100 Electric Scooter

Top Razor Toys Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

Kardoc

Level 3 Expert

7503 Answers

Are you a Razor Toy Expert? Answer questions, earn points and help others

Answer questions

Loading...