Boat on screen does not point the direction the boat is going e-80 series also chart will not go course up or heading up like the radar does unit is set in relative motion mode

What Is A User Chart Point And How Is It Used - Furuno FCR ...

www.manualslib.com > ... > Operator's manual

Furuno FCR-2107 Manual Online: What Is A User Chart Point And How Is It Used. A point is a center point for a sub chart inside a user chart. Sub charts are ...

Furuno Ecdis Fmd 3300 cbt : ??? ???

m.blog.naver.com > sksalwkdus

Jul. 21, 2016 - I can send my Route Plan and User Chart to a FURUNO GPS for display on the ... A point is used to create a Manual Update from a chart object.

ECDIS display

furuno.de > Downloads > Handb?cher1

PDF Open Point page of User Chart. Use Cursor and SELECT button to define location of Points. When you remove selection Enable changes or close User Chart ...

Electronic Chart Display and Information System (ECDIS)

www.furuno.de > Downloads > Handb?cher1
PDF
What is a User Chart Point and for which purpose it is used ? ... points or heads at any instant, has been changed to Heading (Hdg):. · Alarm "2002 No course ...

n the system setup, under “UNITS” I set BEARING to “MAG” (magnetic). This will cause the unit to display course / bearing information in relation to the Magnetic North and match magnetic compass readings. It is not the same as True North! One has to be careful with this setting. There are a number of areas where the earth's magnetic field is locally disturbed, sometimes very significantly. Your GPS may not account for it. - again, under “UNITS” I set “METRIC”.

Your antenna seems to be mis alighned. Its ZERO point must be readjusted.

Gain set too low?

You must have a heading sensor input for radar/chart overlay. (i.e. PG500)

it cannot determine a heading, have you also damaged an internal antenna or positioning / gps device inside it? It is unsure which direction it is pointing in but uses triangulation to determine this.

That requires either an electronic compass unit, or gps to achieve correct heading and hence correct orientation of the radar image

With the charts page up, start by hitting the find ship softkey at the bottom of the screen.If that find the boat on the chart all is good.If not you need to check you have a GPS fix. Go to GPS screen and see you are seeing satalites.
If all is good when you hit find ship and the boat disappears again from chart while underway you will need to go into the chart setup menu and see if the screen amplifier is turned off. If off turn on.This is first place to start. Hope that helps

go into installation mode (hold menu during power on) find radar setup, go to next page, do heading alignment. also tune video, your unit was reset!

It is not likely that there is a software error that could cause that problem so I'm going to cover some basic information first. Forgive me if I'm covering stuff you already know. There are 3 chart orientation modes, North Up, Heads Up, and Course Up. North Up you already know! In Heads Up mode, the chart will only orient heads up when the boat is moving. Unless you have an electronic compass interfaced to your GPS it has no way of knowing which way you are facing. Once you start to move, it compares your new position to the old position to determine which way is heads up. If you are not moving, the map defaults to North Up even if you are in heads up mode. Course Up mode is commonly mistaken for Heads Up. In Course Up mode, the GPS orients the top of the screen toward a waypoint that you have told the GPS to go to. If no waypoint is selected, the GPS will default to North Up orientation. So I guess what I'm saying is, make sure the boat is moving, and make sure you're not in course up mode (unless you want to be).

In the unlikely event that there is a software error causing this problem, it can easily be fixed by getting an update from Standard Horizon. You can either get them to send you an update chip, or download it online and copy it to a blank C Map card. When you turn the GPS there will be a message on the opening screen that identifies you software version. Get that information before you call Standard.