The clip has broken and I cannot find a replacement

First, remove the paper tray from your printer. On a Canon printer, this is done by pressing the release clips located on the right and left side of the paper tray. On an HP printer, press the release button to remove the paper tray. Once the paper tray is released, locate the broken paper tray clip. This clip is usually a plastic piece that is clipped onto the paper tray. Using a pair of needle nose pliers, carefully remove the broken clip from the paper tray. Once the broken clip is removed, carefully inspect the paper tray to make sure that the area where the clip was attached is clean and free of any debris. Next, locate a replacement paper tray clip. You can find these clips online, or at a local office supplies store. Using the same needle nose pliers, carefully attach the new clip to the paper tray. Make sure that it is securely attached to the paper tray. Finally, re-insert the paper tray into the printer following the same instructions used to remove it. Once the tray is inserted, test its functionality to ensure that the new clip is securely in place.

If the plastic blue clip on your Oreck Magnesium vacuum cleaner has broken, you will need to replace it to keep the bag securely attached to the vacuum. Here are the steps to replace the clip:

1. Locate the broken clip. It is usually located on the underside of the vacuum, near the bag opening.
2. Remove the broken clip by gently prying it off with a flat-head screwdriver or a similar tool. Be careful not to damage the surrounding area.
3. Obtain a replacement clip. You may be able to purchase a replacement clip from an Oreck dealer or online retailer.
4. Attach the replacement clip to the vacuum. The clip should snap into place and hold the bag securely.
5. Test the clip to make sure it is properly attached and holding the bag securely.

There should be a few screws and mostly plastic snap clips. If it has come loose you have probably broken some on the snap clips and they are needing replaced. Most auto body supply stores will be able to provide the new clips. Just remove the panel, remove the bad clips, replace with new clips and reinstal the panel.

can the clip be made by you ,if not when did you buy if its been within the last 14 days take it back as faulty,if your handy they are easy to make,you will need spring steel.

You need to replace the brush block assembly

Replacement clips are available through specialty auto parts stores...there are many tricks or solvents that will loosen the glue on the broken clip...if you damage the glass, you can find a popular window replacement, inspect the clip too, at your nearby salvage yard or online...Hope this helps.

use a little of jb weld mix it together where piece broken and let it dry for 6 to 8hrs.

Hi, I don't think you can replace the Just like that,except from a damaged onethat the rim clamp/mount is still present.

You will need to get a new drum kit mic for your drum set, And i would advice whengetting a new drum mic, it's better you buy another product..\

For me i prefer Yoga Drum kits or some other one would do.

Hope that helps...

Its more than you think. 1. Inspect for a broken retaining clip by removing the valve body and then the valve body separator plate. Inspect the forward clutch control valve, spring, retaining clip, and valve body casting for damage (Figure 1).

2. If the clip is broken and the forward clutch control valve and/or valve body casting is damaged, replace the main control. The retaining clip has just been revised to prevent the chance of breakage. The revised Retaining Clip (F8DZ-7F194-AA) has circular cutouts on the side of the clip in place of the square cutouts on the previous design level clip (Figure 2).

3. Inspect the new main control (if required) before installing it and replace this retaining clip for the forward clutch control valve and spring if it's not the new design (Figure 2).

4. Any time service is required on any AX4N transaxle main control, inspect the retaining clip for the forward clutch control valve to be sure it is the latest design level, and replace the retaining clip if it is not. The revised clip is larger and will remain centered in the valve body casting groove. too repair estimate..400-800 dollars...Hope this help..Big shops will hurt yo pockets

Call Sandisk at 1-866-726-3475, or get a broken player off of eBay for low cost and just swap out clips. Now, there is a plastic piece that holds the clip into place - that plastic piece didn't break off, did it? If so, you must replace the entire player.