I need the upper and lower rack rollers replaced but do not know the part numbers. I am looking for a parts diagram on the internet but have been unable to find one. GE Nautilus, Model GSD2200G00CC

Hello Adriana;

My name is Peter. I am a retired field service appliance technician.

The model number you provided does not sound like a model number. Your model number is located on a label on the face of the dishwasher after you open the door or on the side of the door.

Go into the following website and put in your model number. You will get diagrams, part numbers and cost.

Record the part number and search the internet for a better price. Even discontinued items are available on the internet.

Water Filters Lawn Garden Appliance Parts

Hello. From what you're describing, there might be a problem with the rack switch. It is connected directly to the main oven display board at connector P10 for a single oven(See pic 3, left side, middle). On the double oven model, there will be a P12 connector near the same area. TURN OFF POWER TO THE OVEN BEFORE ATTEMPTING TO CHECK ANYTHING!! On the double oven display board, there will be a connector P10 and P12 for the upper and lower oven racks.The part number for the main oven display board is 7316516536 in case the switches are good. The rack switch part number for the upper and lower oven is 7318903403. The part number is the same for the switch in the single oven model. Note the designation on the exploded parts diagram as 14(with a circle around the part). I've included the last pic(the oven relay board) just for future information.The part number for it is 7316443919(dual oven relay board). If you are hesitant about attempting to troubleshoot the oven, definitely call for service! This can be an INVOLVED REPAIR requiring advanced troubleshooting. The connectors on the circuit board can be damaged easily as they are multi-pin devices. You will need a voltage/ohm meter with fine probe tips to perform continuity checks on the rack switch(s). I hope I helped you!

Lower Rack

• Remove all of the dishes from the lower dishwasher rack.
• Pull the lower rack out of the dishwasher so that it rests on the dishwasher door.
• Lift the lower rack up and out of the dishwasher.
• Place the new lower dishwasher rack on the dishwasher door, then push it into the dishwasher.
• Upper Rack
• Remove all of the dishes from the lower dishwasher rack.
• Extend the upper rack as far as it will go.

Remove the two plastic end caps, located on the end of each dishwasher arm. To remove, insert a flat-head screwdriver between the arm and the tab on the outside of the end cap, then lift the tap to remove the end cap.
Pull the upper dishwasher rack straight of out the arms to remove.

Insert the rollers on the bottom of the new upper dishwasher rack into the rack arms, then push the rack completely into the dishwasher.
. Align the end caps with the ends of the arms, then push the end caps into place.

Upper Rack

• Remove all of the dishes from the lower dishwasher rack.
• Extend the upper rack as far as it will go.
• Remove the two plastic end caps, located on the end of each dishwasher arm. To remove, insert a flat-head screwdriver between the arm and the tab on the outside of the end cap, then lift the tap to remove the end cap.
• Pull the upper dishwasher rack straight of out the arms to remove.
• Insert the rollers on the bottom of the new upper dishwasher rack into the rack arms, then push the rack completely into the dishwasher.
• Align the end caps with the ends of the arms, then push the end caps into place.

You just need the wheels. I have bought the upper rack wheels before, now I need the lowers. I have found a site selling them at 10.00 each. I am going to keep looking, I think I can do better, considering I need 4. I might just buy a new washer if I have to spend 40.00 plus shipping! I will post back if I find a better deal.

you need to call your local dealer and tell them the VIN number.
they will be able to tell you the part number for the sliding door roller.
there are upper, lower and side rollers

it sounds to me like you have some severe fuser thermistor and thermal fuse problems ...i would look into getting an entire fuser assembly sharp part number DUNTW7305DS** last digits depend on your location and power supply

I have Ricoh part numbers for the Aficio 3025, which is the EXACT same machine, using the EXACT same parts. And I assume you mean upper and lower "fuser" rollers.

Photoconductor unit P/N B205 0151
Hot Roller P/N AE01 1103
Pressure roller P/N AE02 0161

(http://www.geappliances.com/service_and_support/parts/)
the correct # for your unit is pdw7880n10ss
just enter your model #(under repair or replacment parts)the site will walk you thru the rest.when you get to the parts list make sure you use the diagram to match your part exactly(click the red box at top of page)hope this helps.thanx for using fix-ya!!!

I have a GE Profile model PDW7800.... and just replaced the rollers on one side since one of them had broken. There is a 'magical' way to reinstall the rack so the side guides ride inside the roller guides without touching. I suspect that the rack has not been reinstalled in the precise manner - which I am still trying to figure out. The new roller assembly which attach to the rack fit differently than the original ones. I found that you do have to remove the rollers screwed into the wall to get the glides out and that could also cause rough gliding. Part of the 'binding' is designed, I believe, to keep the racks from coming out too easily.