Question about Arrow Tools & Hardware - Others

1 Answer

WHERE CAN i GET AN ARROW T55 STAPLE GUN PUSH ROD ASSEMBLY?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 205 Answers

Order from Stanley

Posted on Jul 12, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: ASSEMBLY

I just had to repair one of these guns for work. It's a bit tricky, seeing as you are dealing with springs and such...but it can be done. Take your time ...don't set the springs until you have things set in place and lined up. Make sure the pins are in place. Set the flat spring first (it is the toughest) while the handle is depressed all the way in. Gently open the handle and then set the torsion spring. Take your time here...springs are set and they could make all the pieces fly out if you don't quickly get the other half put on it. Hope this helps.8d59edb.jpg

Posted on Feb 13, 2008

  • 2712 Answers

SOURCE: staple gun support

Know the types of staple guns available. They can be manual, electric, battery operated or run by compressed air with an air compressor. Some staple guns have guide wires because they’re used by electricians that can’t pierce wires. Others have long noses to work well in corners and tight spaces. There’s also a reverse built ergonomic staple gun called a "forward action" because the handle and the staple’s exit point are on the same end of the staple gun. Some staple guns can shoot brads instead of staples. Know how each type of staple gun works. This one is so simple because it works just like a stapler. You press and hold the silver latch on the back of the stapler to open the body. Take the tray out and fill it with staples. Then it’s ready to use. Just put the staple ejecting end on your piece to be stapled and squeeze it. There is also the forward action manual gun which is used by pushing the handle down, too. The handle is just located near the staple ejection site. Use an electric staple gun for effortless stapling. There’s no need to squeeze or apply any pressure on these guns. They come with a very short cord so you will always need to have an extension cord with your staple gun. You can also go with a rechargeable battery operated cordless staple gun. They are great but they do run out of steam so for long use one with a cord is better. They’re also pretty easy on the wallet these days, so there’s no reason to go without this in your home tool kit as it’s something that does a lot of jobs. Know the versatility of the staple gun. Whether you have a manual or an electric model, these are some of the most versatile tools out there. You can use them to recover furniture, to build a birdhouse, to staple lattice to a patio, to build lightweight projects like a small knick knack shelf and to do wiring work.

Posted on Aug 27, 2008

smartr10U
  • 1305 Answers

SOURCE: How to load Arrow T25 Staple Gun

at the back end of the handle, there is a retainer spring loaded clip. Push it in, then push it downward toward the base of the stapler, the clip should then release the spring, pull the rod with the spring completely out, slide a row of staple in where the rod came out, ONLY ONE ROW, then insert the rod with the spring back in and push it firmly in, and lift it upward to engage the lock. and fire away... Hope this gets your working

Posted on Jun 08, 2009

efs_perpends
  • 1996 Answers

SOURCE: I have a staple stuck in my Arrow model #ETN-50

Unplug it. If you can see the driver jammed against the staple, take a screwdriver end and try to push the driver back in and the staple should be released. If you can't get the driver to go in and release the staple, you'll have to disassemble it to clear the jam, If you need help with that, see the instructions for the current model here, page three, diagram 3, cleaning the magazine.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Posted on Aug 18, 2009

Testimonial: "Thanks for your help! Much appreciated!"

SRF518
  • 232 Answers

SOURCE: how to open arrow p22 staple gun

there is a spring follower in the base with a hook that latches into the body of the stapler. press in then down to unlatch the follower.

Posted on Oct 21, 2009

Testimonial: "yes thanks very much!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Craftsman 68514


The replacement pack for this gun say the staples are compatible with "Craftsman 68514 and 68517; Arrow Brand T50 Staplers T50 and T55; and Stanley/Bostitch TR110 and BT110 staple guns", so I assume they are also backwards compatible. That's just an assumption though.

Mar 22, 2013 | Arrow Tools & Hardware - Others

1 Answer

How to load staples?


    • 1 Push in the push rod plate on the back of the Arrow T50P and press down to unclip the push rod from the gun. Pull the push rod out of the staple channel and away from the staple gun.
    • 2 Insert a strip of staples into the channel with the tips of the staples pointing toward the bottom of the staple gun.
    • 3 Place the end of the push rod into the staple channel of the gun. The end of the push rod has a small, solid piece of metal that fits into the staple channel.
    • 4 Press the rod all the way into the staple gun until the rod plate engages in the notch at the rear of the gun.

Jun 26, 2011 | Arrow T50P ARROW STAPLE GUN

1 Answer

I don't understand how to load a T-50 staple gun. There are never any pictures of the thing that you push. I think it may have broken off of my gun. If that is true, then it is no good? ...or is there...


we have one, you push in at the back and pull down take out the rod put the staples in and put rod back in and push up it locks itself, hope it helps

Jan 30, 2011 | Heavy Duty Arrow T50 Staple Gun

1 Answer

Can u tell me how to load the staples into my arrow t25 staple gun not used it for a long time


Hello. Here is a link to a free manual for your stapler. http://www.arrowfastener.com/upload/manuals/79055000259_manual.pdf

Look on page 3 for the three steps to load it.
1. Press latch in lower rear of gun to remove pusher rod from machine.
2. Insert strip of staples.
3. Replace pusher rod.

Happy stapling! J.

Jun 22, 2010 | Arrow T25 Staple Gun

1 Answer

I cannot figure out how to load an Arrow T50P staple gun


Turn it upside down. On the end opposite where the staple comes out look for a tab on each side you squeeze to release the staple holder, the staples go in to this holder upside down as well, just push it back in until the releases catch and hold it in. Hope this helps.

Jun 17, 2010 | Arrow T50P ARROW STAPLE GUN

1 Answer

I don't know how to load staples into the Arrow T55 manual power stapler


there should be a spring loaded clip at the end of the stapler opposite from where the staples come out push it in to release

May 27, 2010 | Aerobie Arrow Fastener T55C All Chrome...

1 Answer

Don't know how to load staples in my powershot pro


Usually a black tab toward the back of the staple gun.
Push in, pull up and pull out.
Push rod, spring and assembly should slide out easily.
You can then reload as needed.

Push in, pull up and when the push rod bottoms out push down.
This usually locks the tab back in place. Do this a few times and you will get the feeling pretty quick.

Good luck!

Oct 18, 2009 | Powershot Tool Company Cobra 8000 Forward...

1 Answer

Cannot load staples


At the back of the staple gun is a flat shaped metal piece. It's at the bottom. Push in, pull down, then pull the mechanism out. You'll see it's a metal rod with a spring, that is attached to that flat metal piece. The spring pushes against another flat metal piece, that has a hole in it, and travels back, and forth on the rod.

The flat metal piece that the spring pushes down the rod, pushes against the staples.

Remove this spring mechanism, slide the staples down the rails. The staples will be in the position of an upside down U. Replace the spring mechanism, and lock it back into place. (Push in, pull up)

Should, your question be in reference to the fact that you have staples loaded, but upon pressing the trigger nothing comes out:

In the front of the staple gun, is a flat metal piece that pushes down on the staples. One staple at a time. The flat metal piece is shoved down by spring pressure. The spring pressure is applied to the flat metal piece each time you squeeze the trigger. (Flat metal piece = Hammer)

Sometimes, Two staples try to come out. When they do, this flat metal hammer is stuck up in the gun. To free the flat metal hammer, remove the spring mechanism out of the back of the staple gun. (The spring mechanism discussed above) Remove any staples in the gun.
Try to use a flat blade screwdriver, and see if you can shove the flat metal hammer in the front of the gun -> UP.
(DO NOT have the staple gun pointing at your face! DO NOT squeeze the trigger! DO NOT use excessive force)

If this method is of no avail for you, you have to disassemble the gun, and remove the metal hammer, and stuck staple/s.

Jul 29, 2009 | Arrow T50P ARROW STAPLE GUN

1 Answer

How to load Arrow T25 Staple Gun


at the back end of the handle, there is a retainer spring loaded clip. Push it in, then push it downward toward the base of the stapler, the clip should then release the spring, pull the rod with the spring completely out, slide a row of staple in where the rod came out, ONLY ONE ROW, then insert the rod with the spring back in and push it firmly in, and lift it upward to engage the lock. and fire away... Hope this gets your working

Jun 08, 2009 | Arrow T25 Staple Gun

1 Answer

The staples do not enter the wood completly


often when squeezing the tool the front gets lifted and the staple does not set fully. try making sure the front is tipped down fully and in contact wood when it fires. if that doesnt work the push rod is not working properly and is easier to replace than try to fix

Apr 22, 2009 | Arrow CHROME STAPLE GUN ARROW IND....

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Arrow Tools & Hardware - Others Experts

JOHN LAPIER

Level 3 Expert

2591 Answers

ray gallant
ray gallant

Level 3 Expert

63539 Answers

Poul Brinchs Larsen

Level 2 Expert

159 Answers

Are you an Arrow Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...