Paper is getting jammed in the document feeder

please heed to ahat the technician said and have it replaced for the problem to be solved
thak you.

Hello cockie ,

You can diagnose most problems by checking the control panel LED's for ink out, paper-out or copier problem.
If a problem occurs while you're printing, you'll see an error message in the progress window on your computer.
It may also be helpful to try running a printer nozzle check.

See the following message problems and solutions:

Error Message Probable Cause No color or black ink cartridge - - >
Press the Color Copy button to install a new ink cartridge. The indicated cartridge is not installed or it is installed incorrectly. Color or black ink out - - >
Press the Color Copy button to begin replacing the ink cartridge. The indicated cartridge is out of ink Ink cartridge error - - >
Press the Color Copy button to begin replacing the ink cartridge. There is something wrong with the ink cartridge. Paper jam or misfeed - - >
Press the Color Copy button and clear the paper jam by hand if necessary. Paper is jammed. Press the Color Copy button to clear the jam.
See the User's Guide for more troubleshooting tips. Paper out - - >
Load paper in the sheet feeder and press the Color Copy button. Paper is out. Load paper in the sheet feeder, then press the Color Copy button to continue printing. Scanner unit open - - >
Close the scanner unit. Scanner cover open. Carefully lower the scanner cover and press it down until it clicks securely into place. Scanner error - - >
See your documentation and call Service if necessary. Press the On button to turn off the EPSON CX3200. Check the transportation lock and unlock it, if necessary. Turn on your EPSON CX3200 again. If the error message still appears, contact your dealer or EPSON. Printer error - - >
See your documentation and call Service if necessary. Press the On button to turn off the EPSON CX3200, then press it again to turn it back on. If the message still appears, contact your dealer or EPSON.

Document feeder is jammed

Paper jams - Kodak Printers

If paper is jammed, a Paper jam message will appear on the control panel display.

Follow these steps to clear the jam:

1. Gently pull any jammed paper out of the output tray or sheet feeder.
   
   
2. If the paper is stuck inside, turn off the Epson Stylus CX.
   
   
3. Open the scanner, remove the jammed paper and torn pieces, close the scanner, and turn the Epson Stylus CX back on.
   
   Note: Be sure to check the far left of the carriage area when checking for jammed paper. Paper that is jammed there may be hidden from view.

If paper jams inside the Automatic Document Feeder, clear the jam as follows:

1. Open the Automatic Document Feeder cover and remove any jammed paper.
   
   
   
   
2. If necessary, lift the document cover and remove any paper that has jammed inside.
   
   
   
   
3. Press OK to clear any messages on the display screen.

If you are receiving an Error Code 103 or a Paper Jam error, but there are no pages in the ADF (Automatic Document Feeder), follow the steps below:

1. Close the scanning application (such as PaperPort)
2. Turn off the scanner and the computer
3. If you have a combination ADF with a Flatbed scanner, unplug the ADF cable from the base of the scanner
4. Plug the ADF cable back in
5. Turn on the scanner power
6. Turn on the computer
7. Try scanning again

For a Paper Jam or Error Code 103, make sure that the ADF cable in the rear is connected to the scanner base. Check the flatbed to make sure that it is clear. A page incorrectly placed on the flatbed may interfere with a page feeding through the ADF.

If your scanner stops scanning due to a paper jam in the Automatic Document Feeder (ADF), a warning dialog box appears after a few moments.

To clear a paper jam:

1. Open the Automatic Document Feeder cover.
2. Remove the jammed paper and close the cover.

If you are receiving a paper jam error, or if the scanner is running continuously, check to make sure the paper sensor arm is not stuck down.

1. Open the Automatic Document Feeder cover.
2. Look for the small black plastic arm
3. When you press on this arm, it should move freely up and down
4. If the arm is stuck down, please contact Technical Support for troubleshooting options
5. Close the ADF cover.

I have a Laser Jet 3050..when I try to load a oaoer to copy or fax, paper does not move...just gears moving but paper is not being pick up...any solutions?

first u switch off and switch on the machine, that time ur document feeder get rotating its not feeder problem. otherwise pls u check ur feeder driveres.

Does the adf show a paper jam? If so remove it or look for some thing blocking the paper path and remove it. Also try to turn off the copier and disreconnect the doc feeder and turn it back on and see what happens.

Does it happen both off the copy glass & thru the document feeder or only off the document feeder. If both - check the side guides inside the cassette to make sure they are tight against the paper. If it only happens when using the feeder- the feeder tray needs to be adjusted. There is usually 2 screws under the document tray that when loosened allow for side to side adjustment. Moving the tray should solve the problem if it is only happening when you use the document feeder.