Question about Garden

Open Question

Have yardwork trimmer - lost black top piece after winding on new plastic string so unable to use trimmer.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
StickyBeets
  • 2 Answers

SOURCE: put string on tb425cs troy bilt trimmer

there are two ways to install the string..the cool way is without pulling the inner reel off the trimmer..just leave it in place..cut (2) approx.two arms length (thats spreading your arms out like airplane wings) of .095 string..now, align the arrow of the inner reel (it turns counter clock-wise..the arrow points outward) with the arrow on the outer spool (pointing inward)..holding the spool and reel together so the inner reel doesnt move, push one of the cut strings through the eyehole in the side of the outer spool, and it should come up to the right, through a slot next to a small round hole the diameter of the string..if it doesnt, it just missed the exit (as i call it)..pull out and try again..let about an inch come thru..now take that end of the string and push the line into the little round hole until it stops, which should be about a little more than 1/8 of an inch..hold it in while pulling the excess line outside the spool to keep it in place..now do the same with the other string for the other side..once you have both lines in place, turn the inner reel counter clock-wise to draw in both lines through the eyeholes of the outer spool..you may or may not get all of the line to wind in..not a problem..you will still have enough to do what you need to do..just cut off the rest..one problem you may or may not have that i do most of the tyme is that it gets hard to turn the inner reel..one solution is to bump the top of the 'bump knob' with your fist, then pull both strings at the same tyme, then continue to turn..this method is quicker and easier than the second way of having the inner reel out and trying to wind both lines at the same tyme and trying to place the reel back in the spool..hope this works for you...

Posted on May 19, 2009

Ad
#1 Taper
  • 1041 Answers

SOURCE: Installing new line on my string grass trimmer

Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

Jim

Posted on Jul 03, 2009

#1 Taper
  • 1041 Answers

SOURCE: How do you wind replacement line to the Poulan Pro

If it is a duel line trimmer then:

Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

If it is a single line trimmer, just wind a single piece of string clockwise onto spool.

Jim

Posted on Jul 03, 2009

canbruce75
  • 1776 Answers

SOURCE: how to change string on weedeater trimmer electric

Check out the link that I am providing and see if the video helps you out. Sure hope so and best wishes.

http://www.youtube.com/watch?v=SuGfDNH6fXk

Posted on Aug 30, 2009

  • 133 Answers

SOURCE: B & D auto feed string trimmer won't advance string

Is the string spool seated on the rachet correctly? If so and all is well, it is worth noting that these trimmers auto feed fuunction is problematic at best, requiring manually unwinding some line every few minutes as the unit gets older.

Posted on Apr 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO I INSTALL A NEW STRING IN A PRO CUT 11 for Ryobi RLT30CD trimmer


LINE REPLACEMENT (Fig. 8) (For Reel EasyTM Head) Use 2.4mm monofilament string. Use original manufacturer's replacement string for best performance. n Stop the engine and disconnect the spark plug wire. n Cut one piece of string approximately 7.6m in length. n Rotate knob on string head until line on knob aligns with arrows on top of string head. n Insert one end of string into eyelet located on the side of the string head and push until string comes out through eyelet on the other side. Continue to push string through the string head until the middle section of the string is inside the string head and string outside the string head is evenly divided on each side. n Rotate the knob counterclockwise on the string head to wind the string. Wind the string until approximately 20cm remains protruding from the string head. INSTALLING STRING IN PRO CUT II STRING HEAD Use monofilament string between 2.4 mm and 2.7 mm diameter. Use original manufacturer's replacement string for best performance. n Stop the engine and disconnect the spark plug wire. n Gather two of the pre-cut lengths of trimmer line provided or cut two pieces of trimmer line, in 28 cm lengths. n Insert the strings into the slots located on the sides of the string head. String should be pushed in until approximately 2 cm protrudes from the holes on the top of the string head. n Remove old string by pulling it from the holes located on the top of the string head. http://www.screwfix.com/sfd/i/cat/pdfs/89/p4763889.pdf

Oct 29, 2010 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

1 Answer

How do i install a new trimmer line ie plastic cord that u put in the head of a nylon trimmer


For Black and Deckers: Remove cup from bottom of unit by depressing 2 detent tabs and pulling away from unit. Replace empty spool with new full one or wind on aftermarket string. Wind in direction of arrow on spool. Make sure spool is seated on rachet firmly.

Apr 15, 2010 | Garden

1 Answer

Replacement of Cutting Line! How to do? anneodello


There should be a half sphere-like object on the bottom of the spool where the line goes. Twist counter clock-wise to remove.

If it is a duel line trimmer then:


Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

If it is a single line trimmer: Then just wind a single piece of string clockwise onto spool. This may need to be longer than 7ft.

Jim

Oct 21, 2009 | Black & Decker Garden

1 Answer

I need to rewind the spring and starter pull cord. I need to understand how all the parts fit together


I had the same problem. I had to take it apart and rewind it manually. To do this:
Step 1:
There are 4-bolts to remove on the orange plastic section the screw into the motor housing (one of them is hidden inside the orange plastic housing, you'll see an opening for it). There are also 3 screws in the black plastic exhaust housing that screw into the orange plastic housing, find those and remove.

Step 2:
Carefully remove the engine from the plastic housing. I didn't disconnect the throttle cable or the electric wires (points) just kind of worked around them.

Step 3:
The mechanism is kind of crappy. There are two black pieces with a spring in the middle, and a metal disc on the bottom with a ribbon coil on the underside of it. The top plastic piece is what turns the flywheel when you pull the cord. The spring in between connects the two plastic piece. This is probably what popped out. There is a piece sticking up on one end, which inserts into the hole in the top black plastic piece. If you remove the little guardrail things you can probably remove just that piece. KEEP TENSIONS ON THE PULL CORD. Once you remove that top black piece, it should start to recoil.

Step 4:
If it did recoil, put the spring back in the top plastic piece, and then put the plastic/spring combo back into the the bottom plastic piece, there is a little groove for the bottom of the spring to slide into. Then put the little guardrail screws back on. Make sure the big metal wire thing hasn't slipped down into the shaft of the weed whacker. That needs to go back into the motor, as it is what gets spun and in turn spins the strings. As you start to put the motor back in, you may have to pull on the pull cord a few times to get the flywheel and plastic piece to line up. Once you hear the motor start to catch, then you should be able to wiggle it back into place and put back all of the screws. Then give it a shot. If it pulls out again, you may have to drill a new hole into the top black plastic piece for that spring to slide into (this is the crappy design part).

Step 5:
If the pull cord didn't retract, you need to remove the other two pieces (lower black plastic piece and metal disc with ribbon). The metal ribbon has a nub on the outside that hooks onto a plastic piece in the bottom of the orange plastic housing. You'll need to wind it around once or twice to "charge" the ribbon, then wind the string back on the black plastic piece. The black piece should slide into the center of the metal disc and catch the inside of the ribbon. Once you get these two together, again, make sure the metal ribbon piece is wound once past normal and then you have to slide both parts together down into the housing catching the metal ribbon loop over the orange plastic nub. It's tricky, it took me a few tries. Once you get that you can try and test the pull cord, you'll see it pull out and feel it retract due to that metal ribbon. Then go back and do step 4, where you put the upper black plastic piece with spring back into place and replace the little metal guardrails.

This whole thing took a few tries, and the pull cord still gets stuck out. It's a major pain to say the least, but after the 5th time fixing it, you'll be a real pro.

Aug 16, 2009 | Homelite Mighty Lite Lawn Trimmer

1 Answer

Installing new line on my string grass trimmer


Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

Jim

Jul 03, 2009 | Homelite Mighty Lite Lawn Trimmer

1 Answer

Cub catet weed wacker needs new string and I don't know how to put the string on....


If it is a duel line trimmer then:

Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

If it is a single line trimmer, just wind a single piece of string clockwise onto spool.

Jim

Jun 30, 2009 | Garden

1 Answer

Load new line onto the mighty vt26 17" curved trimmer


If it is a duel line trimmer then:

Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

If it is a single line trimmer, just wind a single piece of string clockwise onto spool.

Jim

Jun 29, 2009 | Homelite Mighty Lite Lawn Trimmer

1 Answer

How to change the string


If it is a duel line trimmer then:

Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

If it is a single line trimmer, just wind a single piece of string clockwise onto spool.

Jim

Jun 29, 2009 | Homelite Mighty Lite Lawn Trimmer

1 Answer

Don't know how to install new string on Echo SRM 2400


Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

Jim

Jun 29, 2009 | Echo Rapid Loader, Trimmer Head

2 Answers

How do you wind replacement line to the Poulan Pro String Trimmer?


If it is a duel line trimmer then:

Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

If it is a single line trimmer, just wind a single piece of string clockwise onto spool.

Jim

Jun 28, 2009 | Poulan Pro Pp125 25cc Gas Straight Shaft...

Not finding what you are looking for?
Garden Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

roeb

Level 3 Expert

813 Answers

john h

Level 3 Expert

21795 Answers

Marvin
Marvin

Level 3 Expert

85108 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...