Question about Onkyo Audio Players & Recorders

Open Question

Best way to set up the 3 different eq settings on onkyo rz830 receiver.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
techman
  • 3130 Answers

SOURCE: cannot hook eq to my receiver

The speakers will not sound right. You dont have two tape monitors on this receiver? You can simply use the tape otput to the EQ input, and then the Tape monitor input to the EQ output leads. Good Luck

Posted on Jun 09, 2007

Ad
dunnbiker
  • 8546 Answers

SOURCE: how to hook up bose series 2 eq to onkyo tx sr 875 receiver.?

I wrote most of this for a different receiver, but if you account for minor differences to your receiver this will work just fine.

There's good news and bad news. The bad news you need a separate amp because a multichannel receiver with Bose 901's attached as recommended for a standard stereo receiver will only sound right in STEREO on stereo analog material. The other speakers around the room are not designed to receive its Active Equalization and if you engage your Tape Monitor you will NOT BE ABLE TO HEAR DIGITAL sources at all. Tape Monitor is for analog stereo material only and on modern AV receivers it disables any digital inputs so you really can't use the Tape Monitor circuit or attached devices for modern digital sources. However, you can still employ the various DSP options to spread 2-channel analog source material around the room. I do.

The good news. I have a setup similar to what you want to do and it works great! I see on the SR875 there are Pre Audio OUTS. This is easy.

A separate stereo amp for the 901's was my solution. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.


Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

Posted on Apr 25, 2009

  • 79 Answers

SOURCE: What is the best way to connect the ONKYO TX SR708 to a SONY XRB TV & HD DVR H-20. I have a HDMI Cables. I currently have the HDMI coming directly to the HDVR and then Optical to the Receiver. i just

HDMI is indeed the best.
After your HDMI, a digital form of audio connection is best - optical is one form of digital. Coax is another, and if using coax make sure you use a good cable.
Sounds to me like you have got it right.
Plenty of dedicated audio forums out there too, such as www dtvforum.info where there is loads of info.
Save you looking, just sit back and enjoy your system!
Happy day.

Posted on Apr 26, 2009

XSdB
  • 80 Answers

SOURCE: best settings on a 9 band eq for rock and r&b

Provided the rest of your system is all tuned an in proper shape, and up for the wattts, the best sound to set, starting with the low end...start with is a slightly elevated above zero (about 1/4 up from zero) then slowly gradually slope it down to 1/4 below zero in middle and then back up to 1/4 above at the high end.

The result is a gently curved V type shape.

Now, knock down the highest 2 or 3 freq bands a few clicks till they are just above zero. (1/8).

This is the curve you would shoot for with a real-time analyzer for SQ, punch and clarity.



Posted on Jun 12, 2009

rteemon
  • 578 Answers

SOURCE: best settings on a 13 band eq for rock and r&b

THAT IS BASE ON HOW YOUR SYSTEM IS SET UP MY FRIEND ADJUSTING ALL THOSE SETTING WONT GIVE YOU MORE BASS

Posted on Aug 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to hook up a DBX 231 to an Onkyo P301


you will need 4 1/4 inch male to rca male cables, use tape monitor (tape out to line in on eq, line out from eq to tape in on receiver, make sure both buttons that control line level on the back of the 231 are set for -20dbv press tape monitor to use eq, turn off to bypass it.

Mar 06, 2014 | DBX Audio Players & Recorders

1 Answer

Bose 901 hookup with Onkyo SR 805 and Onkyo M282 amp and 901 EQ/


The good news. I have a setup similar to what I think you're trying to do and it works great!

The Onkyo M-282 stereo amp for the 901's is the perfect solution. Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

**Onkyo SR805 Pre-Out Front >>> Bose EQ Amplifer IN
Bose EQ Amplier OUT >>> Onkyo M-282 IN

Set the Input Level on the back of the Onkyo to MAX. The receiver controls everything just fine after you run through your level setup routine again.

I was looking a the 12v triggers on both units and it looks like you only have a Zone 2 trigger so that wouldn't work for turning on your M-282. I guess you're going to have to turn it on and off the old fashioned way, like I do mine.

Mar 15, 2009 | Onkyo TX-SR705 Receiver

1 Answer

Bose 901 equalizer


I wrote most of this for a different receiver, but if you account for minor differences to your receiver this will work just fine.

There's good news and bad news. The bad news you need a separate amp because a multichannel receiver with Bose 901's attached as recommended for a standard stereo receiver will only sound right in STEREO on stereo analog material. The other speakers around the room are not designed to receive its Active Equalization and if you engage your Tape Monitor you will NOT BE ABLE TO HEAR DIGITAL sources at all. Tape Monitor is for analog stereo material only and on modern AV receivers it disables any digital inputs so you really can't use the Tape Monitor circuit or attached devices for modern digital sources. However, you can still employ the various DSP options to spread 2-channel analog source material around the room. I do.

The good news. I have a setup similar to what you want to do and it works great!

A separate stereo amp for the 901's was my solution. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out (or one of your analog Tape Outs) >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.


Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

Write off the Tape Out as an input if you use it to extract the Front L&R channels. DO NOT monitor it or you'll chop the 901's out of the signal path AND kill any digital source audio in the receiver.

Jan 12, 2009 | Onkyo TX-SR605 Receiver

1 Answer

How to hook up bose series 2 eq to onkyo tx sr 875 receiver.?


I wrote most of this for a different receiver, but if you account for minor differences to your receiver this will work just fine.

There's good news and bad news. The bad news you need a separate amp because a multichannel receiver with Bose 901's attached as recommended for a standard stereo receiver will only sound right in STEREO on stereo analog material. The other speakers around the room are not designed to receive its Active Equalization and if you engage your Tape Monitor you will NOT BE ABLE TO HEAR DIGITAL sources at all. Tape Monitor is for analog stereo material only and on modern AV receivers it disables any digital inputs so you really can't use the Tape Monitor circuit or attached devices for modern digital sources. However, you can still employ the various DSP options to spread 2-channel analog source material around the room. I do.

The good news. I have a setup similar to what you want to do and it works great! I see on the SR875 there are Pre Audio OUTS. This is easy.

A separate stereo amp for the 901's was my solution. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.


Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

Jan 07, 2009 | Bose 901 VI Main / Stereo Speaker

2 Answers

How do I connect my bose 901 active equalizer to a onkyo tx-sr506


AV receivers are notoriously incompatable for Bose 901s. The problem is the EQ charges the entire system and could damage the surround processor. Some higher end AV receivers, including some of the newer Onkyo models have pre out power in inputs on main or all seven channels.which you could install your EQ directly between pre amp & power amp without damaging processor. You can also add a two-channel amplifier to the pre out jacks front channels and use your recever's remote to control volume.

Nov 30, 2008 | Bose 901 VI Main / Stereo Speaker

2 Answers

Bose 901 equalizer hookup


how do I hook up the bose 901 EQ to a yamaha DSP3090??

Nov 08, 2008 | Bose 901 VI Main / Stereo Speaker

1 Answer

Gemini Sound Products EQ-3000 equalizer


please connect as the following-----1-mp3 out-----to cd in in your receiver.
2-receiver rec out (tape put)----to equalizer in.
3-equalizer out----to tape in in receiver.

Sep 17, 2008 | Gemini Sound Products EQ-300 Home...

1 Answer

Cannot hook eq to my receiver


The speakers will not sound right. You dont have two tape monitors on this receiver? You can simply use the tape otput to the EQ input, and then the Tape monitor input to the EQ output leads. Good Luck

Jun 09, 2007 | Bose 901 VI Main / Stereo Speaker

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

Ted28

Level 1 Expert

5 Answers

 Grubhead
Grubhead

Level 3 Expert

5686 Answers

The Knight
The Knight

Level 3 Expert

76099 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...