How to set the printer for 'Printable sticker paper' with Cricut Explorer Air 2 software.

ask the maker, of the thing what ever it is.

Cricut Explore Air 2
it is no computer and you posted to computers.
is the PC locked or the CRICUT?
basically a sticker maker it is.
wow, odd.
if this odd printer locks out call them.
if the PC locks out ask your PC maker for the PW fix.

open this link and it shows you all the gestures you use on an iPad

Introduction to iOS gestures iPad iPhone

Here is a link to the Explore manual which has Air sections in it. I didn't see any reference to "2" so I'm not sure it's what you need, but check it out!

If your Cricut machine is not cutting all the way through your material, or is only scoring the material, choose a machine below for specific troubleshooting tips. Fortunately this issue can usually be resolved with basic troubleshooting.

• Cricut Explore
• Cricut Personal, Cricut Create, Cricut Cake, Cricut Cake Mini, Cricut Expression
• Cricut Expression 2, Cricut Imagine
• Cricut Mini

correct cut settings.

Remove the blade housing, then remove the blade and ensure that there are not any bits of paper stuck to the blade or lodged inside the blade housing. Ensure that you replace the blade housing correctly into the machine. Once clean, test your cuts again. If the blade and housing are already free from debris, or cleaning it did not help, proceed to 3.

Try an arm buoyancy test: gently press down on the black arms that surround the blade housing and then release them. Do they bounce right back up, or do they stick or rub in any way? If they stick or rub, please contact Customer Care through one of the options below for further assistance. If they bounce right back up when released, proceed to 4.

Increase the machine pressure settings and try your cuts again. If this does not change the cut result, proceed to 5.

Increase blade depth by turning the dial at the top of the blade housing. If this does not change the cut result, proceed to 6.

Perform a Hard Reset on the machine. If this does not help, proceed to 7.

Check your machine's firmware version. If the firmware is not up to date, perform a Firmware Update using Cricut Craft Room, a Gypsy device, or Cricut Design Studio.

Retry your cuts with a new blade housing.

If the machine is still not cutting through materials, or is only scoring the paper, please contact Customer Care through one of the options below for further assistance.

Forced Firmware Update on the machine through Cricut Sync.

Retry your cuts with a new blade housing. If the issue persists, proceed to 8.

Attempt a Format and Restore on the machine through Cricut Sync. Please note that this step should only be taken if all other steps have failed to resolve the issue.

If this does not resolve the issue, please contact Customer Care through one of the options below for assistance.

new blade. If this does not help, proceed to 5.

Adjust/increase the Multi-Cut setting in the Cricut Craft Room cut preview screen and retry your cuts. If this does not change the cut result, proceed to 6.

Retry a cut using a new blade housing.

If the machine is still only scoring or not cutting through the material, please contact Customer Care through one of the options below for assistance.

Hi Anonymous, let's try to help you out. So, as that:

Signing in

You can discover and watch YouTube videos without a YouTube account, but to view your playlists, favorites, and uploaded videos, you must sign into your YouTube account. To sign in with your YouTube account, follow these steps:
Part 1: On your Wii:

1. Open the YouTube for Wii app.
2. Select Sign In & Settings.
3. Select Sign In.

Part 2: On your desktop computer:

1. In your browser, navigate to www.youtube.com/activate.
2. Sign in with your YouTube account.
3. Enter the code listed on your Wii.
4. Click the Allow access button.

there are printer that print directly on cd-dvd (printable ones).
for the ones that dont print them directly there are printable cd-dvd stickers,they are on a4 paper, you print them like any paper and you remove the pre-cutted stiker and put it on your cd.

it could be a software problem. Please make sure that in the software where your printing originated, the paper size is set exactly as compared to the actual paper you use for printing. Example, if you are printing using an A4 paper, make sure that the document is laid out using the A4 setup with correct margins not exceeding the paper's printable area.

This causes the printable area on the page to be that much less (10 3/4 or 10 1/2 on an 11 inch page). The software thinks the paper is 11 inches long and keeps track, down to the micro inch, where it is on the paper. When it reaches the 10 1/2 inches, your printer calls the page done and ejects it. However, the software thinks there is still another 1/2 inch to print (usually the footer area). Now when you insert a new sheet of paper, the software finishes printing the rest of the page (normally a blank footer) and form feeds to the next sheet. To correct what the software thinks the paper size is, you need to run the Preferences application and change the default settings. Select the Printer button. In the next window, select the 'Change Defaults....' button. Change both the Document size and the Paper size to a height of 10.875 and click OK. Try a new document to see if the paper size is correct. You may need to go back and change the height a few times until it is correct (the height changes in .125 increments). Usually either 10.875 (for 1/4 inch forced top margin printers) or 10.75 ( for 1/2 inch forced top margin printers) will work.

Hi,

Epson's ink uses a dift technology so far better result you need to check what brand of glossy or photo paper you can use. You can purchase an epson photo or glossy paper for best results.

Your printer would work best using the list below:

Paper Types

• Supports a variety of Epson plain and photo papers. Supports plain, bond, air mail, Epson Premium Bright White, Glossy Photo Paper, Premium Glossy Photo Paper, Premium Semigloss Paper, Premium Luster Paper, ColorLife paper, Matte Paper Heavyweight, Double-sided Matte, Inkjet Transparencies, Self-adhesive Sheets, Photo Quality Ink Jet Paper, Greeting Cards, High Quality Banner paper; labels; envelopes, Iron-on Transfers and Photo Stickers; Printable CD-R/DVD-R; Panoramic 8.3" x 23.4" Photo Paper

If you may have other questions pls feel free to ask.

Just rate me Fixya if your issue has been resolved.

Cheers.

What application are you printing from? Basically its the software that handles these features

Try this:

Please try the following:

1. Have your document up on your screen.
2. Click on "INSERT" "PAGE NUMBERS".
3. Select the options you prefer (as header or footer), (right, left, center, inside outside, etc.).
4. Make sure that these page numbers are not outside of the printable area or margin area.

If you are placing the page numbers as a footer:

1. Click on "FILE" "PRINT".
2. Click on "PROPERTIES".
3. Click on the "PAPER" tab.
4. Choose "MAXIMUM".
5. Click on "YES".

This will enlarge your printable area so that you can set your bottom margin as small as .12 inches. This will help in printing the page numbers as a footer.

If this does not resolve your issue, please contact Microsoft for further assistance. This particular issue is software related.