Question about Hotpoint Washing Machines

1 Answer

Hotpoint top loader model HW-T808W, displays error code E2 before it starts rinsing, I've tried to change the drain pump but the error still displays.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hotpoint Master
  • 10,322 Answers

Check under agitator for bad cogs or bad belt under unit

Posted on Oct 19, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 136 Answers

SOURCE: error code f 05

An F-05 error message means that the pressure switch is jammed on empty or a problem with pump. The fault is associated with drain out (pump blocked or restricted in some way). Small panel at rear of machine reveals the pump, pull of the two pipes (Plastic clips hard to get off, slide them sideways), remove wire and unclip pump from base of machine by lifting locking tab and sliding to the left, pump can then easily be cleaned.

Posted on Sep 17, 2007

  • 90 Answers

SOURCE: kenmore 3.5 front loader e70 error code

check your pump

Posted on Jan 24, 2008

IFIXALL
  • 869 Answers

SOURCE: LG Top loader not draining water to rinse and spin

YOU NEED TO CHECK THE WATER PUMP,SO LAY THE MACHINE ALL THE WAY DOWN ON ITS FRONT,NOW YOU HAVE ACCESS TO THE PUMP.Remove any debris that may be lodged inside of it.

Posted on Jun 09, 2008

  • 1 Answer

SOURCE: E2 error code

In reading the manual for this coffee pot, it needs to have the descaling procedure run. The manual lists running a mixture of 6 cups water and 6 cups vinegar in a normal brew cycle...twice to clean hard water deposits from the machine. It says to make sure to remove the filter basket. Once the procedure is complete, unplug the unit and replug in to remove the E2 code.

Posted on Sep 01, 2008

  • 197 Answers

SOURCE: Hi I have a hotpoint washing machine model wt761

You have a blockage not allowing the drum to empty.
Check for blockages via the pump filter and the hoses
F05 means blocked pressure switch
If it still won't work come back to me

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does E2 error mean


Generic pump error

Error Code-control panel display "Err2" (Error 2, Error2) ' question ...

www.haier.com/za/help.../washing_machine/.../question/.../t20140313_209219.shtml
  1. Cached
  2. Similar
Mar 13, 2014 - Error message:Drain error, water can be not drained fully within the required drain time (controlled by PCB software). Reason 1. Pump filter is blocked. Solution 1. Please open and clean the pump filter. (Filter access door is on the bottom right, at floor level of the washing machine). Step 1.Push a flat blade ...

How To Fix Maytag Washer Beeping And Error Codes E2 and F3 Front ...

9k=? 5:23 https://www.youtube.com/watch?v=by94vOVmmhQ
  1. Similar
Mar 18, 2017 - Uploaded by Nancy Gurish How To Fix Maytag Washer Beeping And Error Codes E2 and F3 Front Load Washer Stopped, Repair Of ...

Washing Machine Error Codes - Front Load and Top Load Washers ...

https://removeandreplace.com/.../washing-machine-error-codes-front-and-top-load/
  1. Cached
  2. Similar
May 5, 2015 - F9 followed by E1 - (drain pump system error) F5 followed by E2 - (door will not lock) F7 followed by E1 - (motor drive error) "rL" - (remove load) Washer making error beeps - Door has not been opened and closed for at least 3 cycles. Washer beeps when HOLD TO START is touched - Door not closed

Mar 22, 2018 | Washing Machines

1 Answer

Telemann model xqb60-803clps. Why is it displaying E2?


From what I've been able to find on the net, the E2 error code means there is a problem with the drain pump. Is your machine draining properly or is there water left in the tub? The drain pump might be partially clogged and taking too long to drain out the water--start there first.

Nov 05, 2015 | Washing Machines

1 Answer

Error code 32


this error means the drain pump is on when its off this basically means that the control board is faulty and the part of it that controls your drain pump is corroded or damaged hence the reason it cant drain, this is different from a drain pump fault error as it specically relates to a fault with the control board

Oct 09, 2014 | Fisher and Paykel Washing Machines

1 Answer

The problem with xqb90-701 machine comes up with e2 code will noy rinse ,empty or spin


I don't know what the codes are for this washer but it sounds like it has to do with the pump not coming on and pumping out the water. most of these front loaders have a clean out for the pump filter you should find it between the pump and where the drain hooks up to the tub. many times they get clogged with stuff. I worked on a whirlpool the other day that had a large sock stuck in it.

May 09, 2014 | Washing Machines

1 Answer

Why won't my whirlpool model #LSR8233JQ0 go through the rinse cycle or the spin cycle


i have no info on this model, but if its a front loader then you will be looking at your drain pump motor as at the start of the rinse and spin cycles it will need to drain if it cannot it will not even attempt to continue on, so take that little drain pump cover off and have a look inside the propeller it may just be jammed up, if not it may be blocked somewhere along the hose or just a faulty pump altogether, if its a top loader you will be looking for the same thing but if it isn't the pump it will be the lid switch that senses the lid has been shut as all whirlpool top loaders must be able to activate the lid switch or else it cant spin (simply a safety feature to prevent injury), get back to me if you have any questions

Nov 21, 2011 | Whirlpool Washing Machines

1 Answer

Whrilpool duet front loader washer flashes f2


HI. this code represents a Long Drain issue.

If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed.

Press PAUSE/CANCEL twice to clear the display.

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed.

Potential Causes

• Check the drain hose and make sure it is not plugged or kinked
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects
• If the above does not correct the problem replace the pump..

Aug 13, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Nec front loader keep beeping with E2 on the screen


“F02” is a Long Drain error. If the drain time exceeds 8 minutes this error code will be displayed. In addition, a “SUDS” error may also be generated as a secondary error. This is an indication of a drain pump problem and/or clog in the drain line. You will need to check the following:

1. Check the drain hose to make sure it is not kinked or clogged.
2. Check the electrical connections to the pump and ensure the pump is running.
3. Remove the drain pump filter and check for foreign objects and/or debris.

To check the drain pump, click on the following link for step-by-step instructions.


http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front

If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jul 04, 2009 | Washing Machines

6 Answers

Error code E2 (with a picture of a wrench)


E2 means a problem with the fill. The wrench means to contact Hobart for service

Feb 27, 2008 | Hobart 29 in. AM15-1 Free-Standing...

3 Answers

Oe code


I had the same problem. First the grinding noise during the rinse cycle and then after four weeks the OE code. LG had a local repair service come out and he determined that the drain pump was dead and ordered a replacement. Still waiting on part after only 3 days.

Dec 22, 2007 | LG WM-2277HW Front Load Washer

3 Answers

Maytag Neptune Front Loader - E2 error code


The first time my E2 code came on the washer won't rinse or spin. I checked the drain pump to make sure it was working. (1) Take the back off and pull the two drain lines off pump. Be careful the line going to the drain has a backflow flap, make sure you don't tear it.

(2) On the other side where it drains from the washer to the pump is where I found a bobbie pin that had collected lint and was blocking the drain flow.

When it can't drain the E2 code comes on to let you know it won't rinse or spin.

Make sure to unplug machine before removing back,

Hope this helps everybody with E2 problems.

stude
40stude@bellsouth.net

Nov 29, 2007 | Maytag MAH6700AWW Neptune Front-Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1234 Answers

gbob59

Level 3 Expert

3042 Answers

Eric Taylor

Level 3 Expert

590 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...