After my car went for service DIDdriver's information display not available any more and I cannot reset it.How do i set up screen again?

sounds like he mainboard, is the on screen display(volume,input) normal. Try unplugging the power cable for a while

1. Call the service mode to the screen.
NOTE
• Shifting to the service mode is available even when the service call is occurred.
2. Change the screen using [?] / [?] and select [Trouble Reset].
NOTE
• The trouble reset key will be displayed in the service mode only when the service call is occurred.
3. Touch [OK] on the check screen.
4. According to the description on the screen, turn OFF the power switch, and turn it ON again more than 10 seconds after and check to make sure the machine operates normally.

DO NOT CONTINUE TO RESET the code is for the Hot Part called the FUSER. It can catch on fire! And that will ruin a perfectly good day!!!!

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Corrupted firmware. A firmware update is necessary. If you get access to its control menu, do a factory reset, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

I'm sorry that the Camera is displaying the error message. "TURN THE POWER OFF AND ON AGAIN" displays on the LCD screen when the Lens Mechanism is stuck or when affected by any malfunction. If turning the power on and off again does not resolve the error message, try doing a power reset. Please follow the below steps to perform a power reset.



·Turn off the camera.
·Remove the battery pack.
·Press and hold the power button for 30 seconds.
·Allow the camera to remain without power for 60 seconds.
·Reinsert the battery pack.
·Turn on the camera.


Also try initializing the Cameraif you're able to access the Menu items on the Camera. The Initialize option will be available underSetup or Main settings Sub Menus.
If the issue persists again, service is required. Pleaseclick hearto locate the service center near your area.

Thanks for understanding. Please let me know if your require any clarifications.

on some of the vehicles, you turn the ignition key on, but do not start the engine, then press the accelerator to the floor 3 times within 10 seconds, do this pretty fast, then turn key off, then turn key back on again , but do not start, look and see if the maintenance / service light has went out.

Instructions are listed in the owners manual (http://service.us.panasonic.com/OPERMANPDF/PTD3500U.PDF) on pg. 46.

Press the "POWER" button (or the POWER OFF ( I )

button on the remote control) so that a picture is

projected onto the screen.

Press the "MENU" button to display the MENU screen,

and then press the and buttons to move the

cursor to select "OPTION2".

Press the "ENTER" button to display the "OPTION2"

screen, and select "SYSTEM INFORMATION" with the

and buttons.

Press the "ENTER" button.

The SYSTEM INFORMATION screen will be displayed.

Press and hold the "ENTER" button on the projector or

the remote control for approximately 3 seconds.

An item "LAMP TIME RESET" will be added.

Press the ENTER button, and when the "LAMP TIME

RESET" display flashes, press the ENTER button again.

The used hours of the lamp unit will be reset to zero.

SWITCH IGNITION ON WITH ENGINE OFF.PRESS SMALL ROUND BUTTON ON LOWER RIGHT OF THE SPEEDOMETER UNTIL IT DISPLAY ODOMETER.THEN TURN OFF IGNITION SWITCH OFF.PRESS AND HOLD SAME ROUND BUTTON LOWER RIGHT SPEEDOMETER TURN IGNITION TO ON WITH ENGINE OFF.CONTINUE TO HOLD BUTTON FOR AT LEAST 5 SECONDS UNTIL IT DISPLAY INDICATES 000000 AND MAINT REQUIRED LAMP WILL EXTINGUISH.RESETTING IS COMPLETE.

On the main screen type

*#06# for checking the IMEI (International Mobile Equipment Identity).

*#7780# reset to factory settings.

*#67705646# This will clear the LCD display(operator logo).

*#0000# To view software version.

*#2820# Bluetooth device address.

*#746025625# Sim clock allowed status.

*#62209526# - Display the MAC address of the WLAN adapter. This is available only in the newer devices that supports WLAN like N80

#pw+1234567890+1# Shows if sim have restrictions.




*#92702689# - takes you to a secret menu where you may find some of the information below:

1. Displays Serial Number.

2. Displays the Month and Year of Manufacture

3. Displays (if there) the date where the phone was purchased (MMYY)

4. Displays the date of the last repair - if found (0000)

5. Shows life timer of phone (time passes since last start)


*#3370# - Enhanced Full Rate Codec (EFR) activation. Increase signal strength, better signal reception. It also help if u want to use GPRS and the service is not responding or too slow. Phone battery will drain faster though.

*#3370* - (EFR) deactivation. Phone will automatically restart. Increase battery life by 30% because phone receives less signal from network.

*#4720# - Half Rate Codec activation.

*#4720* - Half Rate Codec deactivation. The phone will automatically restart



If you forgot wallet code for Nokia S60 phone, use this code reset: *#7370925538#
Note, your data in the wallet will be erased. Phone will ask you the lock code. Default lock code is: 12345



Press *#3925538# to delete the contents and code of wallet.



*#7328748263373738# resets security code.

Default security code is 12345



Unlock service provider: Insert sim, turn phone on and press vol up(arrow keys) for 3 seconds, should say pin code. Press C,then press * message should flash, press * again and 04*pin*pin*pin#





Change closed caller group (settings >security settings>user groups) to 00000 and ure phone will sound the message tone when you are near a radar speed trap. Setting it to 500 will cause your phone 2 set off security alarms at shop exits, gr8 for practical jokes! (works with some of the Nokia phones.)



Press and hold "0" on the main screen to open wap browser.