Question about Televison & Video

1 Answer

How to repair tv no power model ct-21z57mq

No power only red light blinking

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Televison & ... Master
  • 18,060 Answers

There is not much information about that unit. Unless you have experience in using electronic troubleshooting equipment to look for faulty parts, I would replace the whole thing.

Posted on Apr 25, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ctf1800
  • 4402 Answers

SOURCE: MY tV will not power and red light keeps blinking

http://www.keohi.com/keohihdtv/brandspecific/toshiba/quickfix/flashing_led.html

Posted on Dec 05, 2007

  • 1 Answer

SOURCE: Red Blinking Power Light Sharp Aquos

What do three blinks of the power light mean on my Sharp Aquos LC-C5262U? I cannot power up my display.

Posted on Sep 07, 2008

  • 4 Answers

SOURCE: blinking red lights

Take out all the cables (HDMI,POWER,RCA,etc...) and then plug just the power back in and see if the TV turns on, and make sure when you take the power cable out, take it out from the back of the TV, when you plug it back in it should click. 
If the TV powers up then try plugging in your HDMI cables and see if that works.


Posted on Feb 20, 2009

  • 1 Answer

SOURCE: Red blinking light on a Magnavox Plasma TV

Here is the solution. For less that 100$ your Magnavox Plasma TV. Model # 50MF2310/37 will be running like a champ.

Issue:

Magnavox Plasma TV. Model # 50MF2310/37 screen has no picture. There is no sound, TV comes on and then after a few seconds clicks and screen remains blank.

Cause:

On the main power circuit board to Capacitors are prone to failure from over load. The caps are 3300uf 10v 105+c capacitors located to the left of the AC power input.

Service:

Magnavox will refer you to a service center. They will advise $$$ for an inspection. They will also want to charge upwards of 500$ to replace the entire board.

Solution:

1. Unplug your TV
2. Disconnect all connections from your TV
3. With assistance lay your TV on its face on a non-scratching service
4. Remove the back panel screws.
5. Lift back panel off
6. The central board is your main power board.
7. Remove all wire harnesses from the main board.
8. Remove all screws that are holding the main board in place.
9. Lift the main board out and carefully place it into a non electromagnetic pouch.
10. Take the board to a Circuit Board repair shop.
11. Have them replace the the above mentioned Caps.
12. Re-install the board in your TV.

NOTE: Replace the caps with 3300uf 16v 105+ high temp caps(preferrably Japanese caps)

This fix cost me 80$ and my time to search for other who had the same issue. Try searching for Magnavox Plasma TV. Model # 50MF2310/37 bad circuit board or Magnavox Plasma TV bad capacitors or Magnavox Plasma TV bad ciruit board.

Hope this all help, Magnavox is should take ownership for this problem and recall any tv's that have these caps in them. The worst part about this is that teh **** from the repair center that was paid 100$ to check the TV, stripped out the screw holes and damaged the case for the TV.

Portland Laptop Repair was awesome. They repaired the board and it looked like new. Check them out at http://www.laptopportland.com/

Jeff G
Portland, OR

Posted on Apr 28, 2009

gripfitter
  • 557 Answers

SOURCE: Panasonic Plasma TV - Model # TH42PX77U does not

This is a difficult question to answer completely. 7 blinks indicates that one of the C boads has failed. however, there are several an SC,SD, SS and SU.
The procedure is to disconnect each of there boards until the blinking is eliminated. The labor charge is usually around 200.00 and the cost of whichever board is bad. Hope this helps.

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a Panasonic CT-36HL44J hdtv, power supply is good, when powered up it acts like it wants to start but immediately shuts off, power indicator light blinks 8 times then pause then 8X (repeat). Spoke to...


According to a service forum (not FixYa), 8 blinks indicates Driver SOS 3 SS Board (SS energy recovery circuit) - in other words, the 8 blinks means a protection code for a faulty board/module. Unfortunately, this may not be repairable at consumer level; the TV will have to go to a workshop to have that board (if this model has it) examined and/or replaced (manufacturers no longer provide individual components for replacement; they lean towards replacing entire boards/panels/modules in their appliances nowadays). The only problem here is the likely cost(s) involved.

I suggest that you obtain a quote from an authorised Panasonic service centre, then you can decide for yourself if it is economical or worthwhile repairing. It's up to you.

- the error code/circuit failure can vary over different models.

Feb 04, 2011 | Panasonic CT-36HL43 36" TV

1 Answer

Power surge-no picture or sound, just red blinking power light


Any malfunction associated with a blinking redlight usually indicates a circuit problem or defective component. Unfortunately, the days of taking off the back cover of your TV and replacing a defective tube or fuse are long gone. Proper servicing will require troubleshooting procedures that can only be performed by a qualified electronic repair facility or professional television repair person. Ask for an estimate and a realistic appraisal of whether the set can be adequately fixed. Depending on the age and condition of your TV it may not be cost effective to repair.

Sep 13, 2009 | Panasonic CT-36HL43 36" TV

1 Answer

Red light power blinking


power supply problem this can be done by a professional tv repair

Sep 12, 2009 | Panasonic Viera TX-32LX70 32 in. LCD TV

1 Answer

MY tV will not power and red light keeps blinking


Check Horiz Out Transistor and we go from there....T.

Dec 19, 2007 | Panasonic CT-32SX31 32" TV

2 Answers

After power outage, tv doesn't turn on


First, the blinking light is a code, how many blinks? Second, regulators are not resettable. Don

Aug 17, 2007 | Panasonic CT-36HL43 36" TV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76046 Answers

Cindy Wells

Level 3 Expert

5866 Answers

Marvin
Marvin

Level 3 Expert

84619 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...