Question about Frigidaire Ovens
My oven burnt up and I need to replace it. Do you have a current oven that will fit the cut out of the that model
I know this isn't directly answering your question, however, what "burned up" about it?
You can get just about every part that fits that oven from Sears PartsDirect. Control boards, bake elements, convection fans, switches, replacement glass... just about everything.
Unless the oven literally burned through the side/top walls, you're most likely going to save money by fixing whatever's wrong with it.
Even the clock/timer control board is only $164 for the OEM part.
Posted on Apr 18, 2019
FIXYA HAS NO IDEA WHAT WILL FIT GO TO A STORE PERSONALLY AND FIND WHAT YOU NEED
Posted on Apr 18, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
The F9 error message usually means that the oven temperature is above 600 degrees F. Check that the fan is operating. Make sure that it is not blocked. Make sure the vent areas are not blocked. There could also be a welded relay contact or high resistance in the oven sensor leads or connections.
Posted on Oct 02, 2007
Midwest Appliance Parts
2601 West Diversey
Chicago, IL 60647
- Toll Free
Supply a wide range of hotpoint oven heating elements
Posted on Apr 11, 2009
When the bake igniter becomes weak or burns out, your oven will not bake. The bake igniter is usually mounted on the oven burner. It's about 1 inch by 4-8 inches (depending on the model), and comes in round or flat styles. If you don't see the igniter glow at all, it's probably burned out. Replace the igniter if found defective. Note: one of the exceptions could be that your oven is set to automatic mode instead of manual. If this is the case, set your oven to manual mode and check again.
If the bake igniter glows red and not bright yellow or white, it is probably because it is too weak. When this happens, the safety valve will not let the gas out into the oven burner. A weak igniter must be replaced.
A faulty igniter is probably the most common cause, however there are others:
Posted on Dec 17, 2009
You have to open the door all the way through.
Then remove the two locks from the hinges.Pull the tabs out, help yourself with a screwdriver.
Grab the door firmly on both sides, pull up the top of the door and slide it out.
Here all diagrams and parts for your appliance.
Posted on Mar 04, 2010
That seal you should be able to order from any appliance spares supplier the Zannussi part number is. 3577252020. cost in euros. € 10.20 + vat.If it is the one I think it is then it is not easy to fit.The screws around the whole front panel have to be slackened off and the front prised forward dont take off fully pull old one off the new one has to be pushed in behind lip then fix all screws.may be easier with door off.
Hope I helped.
Posted on May 07, 2010
Testimonial: "Many thanks for your advice regarding the replacement door seal on my Zanussi oven. It does sound a little complicated to do the replacement, it may proove better to ask if the seal can be fitted by an expert repair man / woman, rather than me/ husband. I shall ask my local appliance shop for a cost price. I thought it may have been a quick D.I.Y. job thaks very much for your assistance "
Tips for a great answer:
Nov 27, 2016 | Frigidaire Ovens
Apr 02, 2011 | GE JKP15 Electric Single Oven
Mar 03, 2017 | Ovens
Feb 23, 2018 | Ovens
Mar 07, 2010 | Frigidaire FEB24S2AS / FEB24S2AB Electric...
Mar 04, 2010 | Frigidaire FEB24S2AS / FEB24S2AB Electric...
Jan 05, 2009 | Frigidaire FEB24S2AS / FEB24S2AB Electric...
Sep 25, 2008 | GE Ovens
Jun 13, 2008 | Ovens
50 people viewed this question
Usually answered in minutes!