Question about Generac Electrical Supplies

1 Answer

My Generac generator model 10kw starts it's exercise timer, runs but won't shut off. Any ideas?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 246 Answers

It is common to cut off the fuel supply by stopping the diesel engine to shut off the transmission of fuel or air. The method is to install the solenoid valve on the pipeline of oil or gas supply, and control the opening and closing of the solenoid valve by pressing the electric button. So the solenoid valve is out of control. It can't cut off the fuel and air.

More technology supports, suggest you to contact the Starlight manufacturer( diesel generator set), they supply Cummins, Volvo, Perkins generator and provide services supports, the email address: sherly@dieselgeneratortech.com.

Posted on Sep 21, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
CarlGehrke
  • 169 Answers

SOURCE: 10kw Generac shut down overspeed

Make sure that the throttle linkage is all there and not damaged/misadjusted, then get a manometer and check your inlet gas pressure. Gas pressure should be 8 inches of water column and stay there running or not.

Carl

Posted on Apr 06, 2009

mydogisk
  • 50 Answers

SOURCE: Guardian generac 10kw model 5502 does not output correct voltage

the instructions says the voltage regulator is automatic/digital. when you check the voltage is there any load on the generator? if applying load to the generator doesn't help, you can manually change the motor speed where the governor connects to the carborator, but it may change the frequency, but the regulator may fix it

Posted on Apr 13, 2009

protek480
  • 1730 Answers

SOURCE: The generator starts up runs for about 15 seconds and shuts down.

Check the oil pressure switch



If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Posted on Aug 21, 2009

  • 384 Answers

SOURCE: 10kw Generac Guardian not cranking, shows rpm sense loss

Sounds like Generator mode switch should be "ON".

Posted on Sep 08, 2009

  • 1 Answer

SOURCE: Generac Guardian 15 kw overspeed fault

Did you remember to set the overspeed shutdown threshold on the control board?

Posted on Jun 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix an overspeed problem with my Standby Generator?


have the dealer look at it again
I suspect that there is a spring missing from the rod that connects the governor lever to the carby butterfly
It's purpose is to act as a dampener to stop the excesses of the fluctuations on start up

Aug 02, 2015 | Generac Guardian 10kW Model : 5871

1 Answer

Generac gen 10000xp will not start not getting fuel


Is there fuel in the carburetor Bowl?
did you try running a separate gas line from a different gas tank to the carburetor?

Apr 01, 2014 | Generac XP10000E XP 10000 E 5932 Portable...

1 Answer

I'm Looking for a Manual for a Dayton Generator Model 4LM41A


Could be it's in the exercise mode. And when the exercise period ends it's shutting down.
Generac might have made this unit for Dayton.
Phone: 1-888-GENERAC (1-888-436-3722)

Jul 11, 2012 | Electrical Supplies

1 Answer

I have a 10KW SIEMENS generator Model #0059090 - Cat#ASGNO10RBS, it was installed May 26-2011.Generator workrd fine after runing all the test required. We had a very short outage less then a minute, after...


Most of those chargers have a fuse in line between the battery and the charger which you should check. They are two stage chargers meaning when there is a large voltage drop, they go to a high rate charge until battery voltage reads about 14.3 - 14.6 VDC then drops to a float volatge and normal float voltage should be about 13.33 VDC. When they go to a high rate the light turns red, when they go to float the light turns green. When the fuse blows the light stays green because it doesn't see any voltage but the charger isn't doing any work.

Jun 23, 2011 | Generac Electrical Supplies

1 Answer

Guardian generac 10kw model 5502 does not output correct voltage


the instructions says the voltage regulator is automatic/digital. when you check the voltage is there any load on the generator? if applying load to the generator doesn't help, you can manually change the motor speed where the governor connects to the carborator, but it may change the frequency, but the regulator may fix it

Apr 12, 2009 | Guardian Electrical Supplies

1 Answer

10kw Generac shut down overspeed


Make sure that the throttle linkage is all there and not damaged/misadjusted, then get a manometer and check your inlet gas pressure. Gas pressure should be 8 inches of water column and stay there running or not.

Carl

Apr 06, 2009 | Guardian Electrical Supplies

2 Answers

Generac Guardian 15 kw overspeed fault


Did you remember to set the overspeed shutdown threshold on the control board?

Apr 03, 2009 | Generac 13,000 Watt / 13,000 Watt Home...

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Generac Electrical Supplies Experts

Sheldon Dedek

Level 3 Expert

909 Answers

Bob Janelli

Level 1 Expert

26 Answers

JOHN LAPIER

Level 3 Expert

2591 Answers

Are you a Generac Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...