Question about Amana Washing Machines

Open Question

My Amana washer shuts off after a minute in wash cycle

If I turn it off and start again it goes another minute yet all other cycles seem to be fine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
dididsaythat
  • 291 Answers

SOURCE: Washer knocks half way thru wash cycle and never gets going in spin cycle

What kind of washer and do u have a model #

Posted on Aug 28, 2007

Ad

SOURCE: GE WASHER WON'T GO THROUGH THE DRAIN CYCLE AFTER WASH CYCLE

Most likley it's the drain pump! check the wiing and pump

Posted on Jul 09, 2008

jumptrout51
  • 3361 Answers

SOURCE: amana washer only works on delicate cycle

Open the control panel. Unplug the timer and then plug it back in good and firm.
If it does not work correctly after that,
Replace your timer.

Posted on Mar 12, 2009

  • 1 Answer

SOURCE: GE WCVH6260 Front Load Washer

I removed the three screws, and lower cover cleaned the few pennies, screws and nasty gunk build up from the filter. The wash machine seems to function as it did prior to the clogged issue. Thank you everyone !!!

Posted on May 31, 2009

  • 1 Answer

SOURCE: frigidaire washer model #fwt425rhso

This is the second time I have had to replace the drum/support shaft on this washer. Not only is it expensive, but very difficult to replace. Probably the very worst washer on the market for this reason. And I only do 3-4 light loads of laundry per week. A definate design flaw on the part of the manufacturer.

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a DIY solution to my Amana washers problem?


It's a computer too. discommect it from power for 15 minutes and re-plug it. start initial setup again. Here is the link to the manual.
https://www.manualowl.com/m/Amana/NFW7300WW/Manual/206242tj3x46

Oct 02, 2015 | Amana Washing Machines

1 Answer

What does error code 6P mean on an Amana washer model LW9203W2B


SH: Open thermistor. Unplug appliance and let rest for 15-30 minutes, then plug back in. If code continues, unplug appliance and call for service.

bP: Pressure switch error sensed. Washer will not operate when this error is displayed. Check for pinches or kinks in the water inlet hoses and straighten if necessary. Check the water inlet hoses filter screens and clean if needed. Verify that the water supply is turned on. Unplug washer and let rest for 15-30 minutes, then plug back in. If code continues, call for service.

rP: Water supply problem in spin cycle. Check for pinches or kinks in the water inlet hoses and straighten if necessary. Check the water inlet hoses filter screens and clean if needed. Verify that the water supply is turned on. Unplug washer and let rest for 15-30 minutes, then plug back in. If code continues, call for service.

LO: Lock Out mode. To activate, press START and STOP/OFF pads at the same time. To deactivate, repeat the procedure.

AU: Flashes when a factory preset cycle is put on hold. A normal function.

Clean Filter: Flashes when a cycle is selected as a reminder to clean the filter before starting a cycle for optimum drying results. Code clears when the door is closed and the START pad is pressed.

Dec 29, 2009 | Amana Washing Machines

2 Answers

Kenmore washing machine model 110 wash cycle stops


DOES IT DO THIS ON EVERY WASH OR SOMETIMES? IF SOMETIMES, CHECK LID SWITCH( THERE'S A LITTLE HOLE WHEN YOU OPEN THE LID, ON THE LID SHOULD HAVE A LITTLE PLASTIC PIECE THAT GOES IN THAT HOLE. THE SWITCH IS UNDER, INSIDE THAT HOLE. YOU CAN GET A PEN OR KEY TO SEE IF IT'S BROKEN.)
\
BOYNISMO@YAHOO.COM

Aug 21, 2009 | Kenmore Washing Machines

1 Answer

Spin cycle stopped on 10 yr old Amana washer


its the brushes on your motor or your pump is blocked or defective

Jun 23, 2009 | Amana 3.2 cu. ft. Top-Load Washer

1 Answer

TIMER ON WASHER MAKES A TICKING SOUND DURING CYCLE


HI, this timer is faulty and, these are early warning signs of potential failuer of this device in the near future. i would prepare to replace the timer control soon. the actual mechanism is showing signs of breakdown.

May 23, 2009 | Amana 3.2 cu. ft. Top-Load Washer

5 Answers

NFW7200TW washer won't engage spin cycle


We had the same problem with the same model machine and solved it.

Our machine was a month old and started getting stuck at minute 8, so we arranged service calls through Amana customer service. Long story short, the first three service reps couldn't figure out the problem. Two of them called Amana's in-house tech support line and the Amana techs didn't know what the problem was. The fourth repairman was smarter than his predecessors. He called the Amana in-house tech line, spoke to a rep who didn't know what was wrong, and then called in again. He explained that. based on his experience, some in-house techs knew more than others. That turned out to be the case because on his next call-in to Amana, that rep knew exactly what the problem was and recommended replacing the main computer board module. The repair guy ordered and installed the part. The machine has been working perfectly for a month.

Dec 25, 2008 | Maytag NFW7200TW Front Load Washer

1 Answer

Amana Top Load washer


you mean you changed plugs on it
if this is the case then you might have a bad ground in which this is plaeging you

Jun 10, 2008 | Amana NAV8800E Top Load Washer

1 Answer

Amana Top Load Washer model# LW3502W Washer leaks water somewhere between wash & rinse cycle best I can tell...drain hose checks out fine. At beginning of wash cycle the first minute or two of agitation...


Sounds like the water seal is damaged and the leaking water has damaged the top bearing which is just below the water seal. You will need to have the hub & seal kit replaced.

Oct 30, 2007 | Amana ALW480DA Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Washing Machines Experts

Sal De

Level 3 Expert

2699 Answers

Mike

Level 3 Expert

4357 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1479 Answers

Are you an Amana Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...