Question about Boating

Open Question

Installed HDS 10 (no touch screen), and ethernet box for total scan transducer. Unit will not show total scan for install? Also, HDS 7 (no touch screen) on front all scrambled. Help!!!

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Editor925
  • 285 Answers

SOURCE: Mounting a sonor/transducer on a MinnKota Riptide ST

Did the unit come with a strap to mount the transducer to a bow mount electric? Most units do... If not there is probably one available for the unit as an aftermarket accessory or accessory from the manufacturer... Regarding the transducer wire, just wrap and rout this up the front of the bow mount motor shaft so when you pull the motor up and secure it, it is not going to get in the way. You could cable tie the cord down near the bottom of the shaft and one up near the top where they wont interfere with the motor bracket when the motor is positioned up on the boat.

Posted on Mar 17, 2009

Ad
  • 1 Answer

SOURCE: Fast ethernet LAN drivers not installed and gives error code 10

Go to setting,control panel,system,device manage then click the network adapter,then properties,in resources uncheck the box "use automatic settings" then click the change setting then "edit input/output range" and try using other value with no conflicting device then click ok.Then go back to device manager and check if the yellow exclamation point is still there

Posted on Apr 30, 2009

  • 1 Answer

SOURCE: Transducer for LOwrance HDS-5

is the HST-DFSBL lowrence transduser combatible whith HDS-5 unit?

Posted on Jun 06, 2009

  • 1 Answer

SOURCE: lowrance x135 not functioning properly

Had the same issue with another brand. Turned out the transducer cable was picking up noise from other cables (power, trolling mtr. etc). Try moving the transducer cable away from any other cables. I put the cable in a 1/4 " plastic housing up to the point where it was above deck and it stopped all the strange stuff. Not sure about the temp issue??

Posted on Jul 21, 2009

  • 9 Answers

SOURCE: i have asus p4pe x/se and installed a 32bit

Asus doesn't list any windows 7 Drivers for this board and
Broadcom says of the windows 7 Driver for this series:
This driver does not support BCM5700, BCM5701 and BCM5702 devices. To use these devices under Vista, Windows Server 2008, Windows Server 2008 R2, or Windows 7, please use the XP or Win2K3 driver above.



So here is the link to grab the Windows XP/2K3 drivers: Good luck!
http://www.broadcom.com/support/ethernet_nic/netxtreme_desktop.php

Posted on Jan 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a map chip & onwers manual for a Lowrance HDS 5 like insight. Serial no. 102574610. Where can I get them?


here is the manual

HDS-5, HDS-7, HDS-5m & HDS-7m - Lowrance

https://www.lowrance.com/.../Lowrance.../HDS-5-7-5M-7M_OM_EN_988-10041-00...Sonar references do not apply to the HDS-5m and HDS-7m GPS only units. Manual Conventions. When you are instructed to press a button in this manual, the ..

Software Upgrades here

Lowrance HDS 5 Software Google Search

and finally Mapping

mapping for Lowrance HDS 5 Google Search

and specifically, INSIGHT

Insight Genesis - Download free Lake, River and Coastal Maps

https://gofreemarine.com/insight-genesis/Make your own maps and download free maps from the community. Insight Genesis' cloud-based software does all the work, automatically processing ... with sonar signals from your existing Lowrance, Simrad or B&G transducer. ... The cloud automatically backs up all your data, protecting against lost or damaged SD cards.

Jun 26, 2017 | Lowrance Boating

1 Answer

How to set up overlay data on a touch 7


HDS 7 Gen2 Touch Touchscreen Fishfinder Chartplotter
this is a link so you can download a PDC file of your operators manual.
on your has 7 push the pages button on the upper right hand corner of your unit. Then refer to page 18 of your manual to change your overlay data.
This should get you headed in the right direction.

Aug 01, 2014 | Lowrance 000-10767-001 Hds-9M Gen2 Touch...

1 Answer

HDS Gens Touch shows positive red to negative & black to positive?


Lowrance may have goofed on the manual printing. RED is Positive, Black is negative. All these systems have reverse polarity protection. If you wire backwards, the screen will flash on and then automatically turn off.
I install these systems and I have always put the fuse hlder on the positive line at the battery. The fuse holders are always red wires and that may also lead to some confusion if they suggest attaching that to the black lead.
Hope this answers your question.

Jan 05, 2013 | Lowrance 000-10767-001 Hds-9M Gen2 Touch...

1 Answer

Lowrance HDS 5 Sonar faulty


You realise we are FIXYA, we are not Lowrance?

Is this when you are moving, or when you are stationary? If it is stationary, then the transducer or the wiring to it, or the plug into the head is faulty.

If it is only when you are moving, the transducer is not sitting at the correct angle and you are getting a disrupted water flow over it.

The other possibility is that you have the sensitivity set too high, which shows more activity on the screen. Set the head back to Defaults.

Feb 11, 2018 | Lowrance Hds-5 GPS Receiver

1 Answer

Got a HDS 5 and im getting bad or false on my sonar when traveling showing fish and structure.When trying to hold ground and im backing up it doesn't even read?i have it on auto sensitivity


Check the mounting and cable connection of the transducer on the stern. If loose will tilt during movement, in reverse wakes from the prop. CAREFULLY check unit during these conditions. The transducer needs to be completely submerged. Good Luck.

Jan 13, 2012 | Lowrance HDS 5 X Sonar ()

1 Answer

I have just bought a LSS for my boat .On the transom i have already a transducer for my HDS and also a speed wheel .my question is can i remove the speed wheel and put my side scanner next to the HDS...


well if the side scanner is a stern mount. Then opposite side would be best and scanning away from other transducer. Too much wattage and they will mix signals and give you two blank screens. You can mount together but run one at a time. Aloha

Feb 09, 2018 | Lowrance LSS1 StructureScan Sonar (Lss1...

1 Answer

Trying to figure out how to start up my fuel guage on my Lowrance


You need to purchase a EP 60 fuel flow meter. Once you have it installed in your boat, you need to monitor it. You set it up under NMEA DEVICES on your setup menu,

Jun 18, 2009 | Lowrance Lcx 28c Hd 7" Gps Fish Finder...

1 Answer

Transducer for LOwrance HDS-5


is the HST-DFSBL lowrence transduser combatible whith HDS-5 unit?

May 02, 2009 | Raymarine B60 12 Tilted Element Transducer...

Not finding what you are looking for?
Boating Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boating Experts

ray gallant
ray gallant

Level 3 Expert

64247 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

29144 Answers

Tom Chichester

Level 3 Expert

54189 Answers

Are you a Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...