Question about NordicTrack Exercise & Fitness

Open Question

My Nordictrack t7.0 belt won’t move. Turns on, inclines but the belt don’t move. It just beeps and goes up and down but doesn’t move. It seems like the start button doesn’t do anything.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 40 Answers

SOURCE: Nordictrack motor will not run when start button is pushed.

Likely the cover of one of the motor brushes popped off. Unplug the machine before you pop it back in place, then try it again.

If that doesn't work, most likely it's the motor control board, or possibly the console, or finally just a loose connection behind the console.


But most likely, it's the motor brush cover. I've been seeing that alot with this model.

Posted on Nov 01, 2009

Ad
  • 103 Answers

SOURCE: NordicTrack Z7xi treadmill console buttons not working

Hello there. It sounds as if you may have a button stuck on your console. Thus not allowing any other buttons to be pushed. (i.e. the 4 beeps). This is usually caused by the i-fit buttons (silver buttons on the front). If the machine is only 4 months old you should still be under warranty (1 year) I believe. This problem in most instances requires the console be replaced. You can contact nordictrack through iconservice.com or by using the number on the fron of your users manual.
Good Luck! Tim

Posted on Dec 16, 2009

  • 218 Answers

SOURCE: My Nordictrack treadmill seems to

it is trying to calibrate itself, let it go the whole way up and then down without interrupting it. Then it should be fine.

Posted on Aug 11, 2010

  • 3247 Answers

SOURCE: I can't get the control panel to reset. The

II might need the actual model number. However, you can go to page 9 on this manual and check if the flashing options can fix the problem. I am assuming you have already tried to turn the power off and back on.

The ohter thing to try is the reset sequence. Within 6-7 secs press High Temp/ Heat Dry/ High Temp/ Heat Dry/ High Temp/ Heat Dry. All lights should light up, press Start button to exit.

Posted on Jun 24, 2011

ercupa190
  • 12223 Answers

SOURCE: Nordictrack COmmercial 1500 console buttons don't work

http://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnes

11_17_2011_8_43_24_pm.gifsincerely. Please keep me in touch.

Posted on Nov 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont my (floor model) nordictrack T9 Ci work? unplugged it and plugged it back in and it keeps going through the start up and then the buttons don't work.


Likely your incline switch is jammed or defective. Could also be that the panel circuit is defective and needs replacing. This panel circuit would need to be removed and tested to pinpoint the exact issue.

Oct 16, 2014 | Nordic Track Nordictrack T9 Ci Treadmill...

1 Answer

What is wrong with and how can I fix the incline on my Nordictrack commercial 1750 treadmill?


This sounds as though the motor is bad, they cost around $130.00, ther is a n electronic controller that controls it, but as it is trying to raise I would think that the switch and controller are functioning. Best of luck and please post back f this helps.

May 25, 2014 | Nordic Track Commercial 1750 Treadmill...

1 Answer

My New Nordictrack c900 pro turns on but does not run.


You probably pinched some wiring during assembly. Could be the controller but more likely the wiring.

Jan 03, 2018 | Nordic Track C900 Pro

1 Answer

My Nordictrack X9i treadmill console says it is operating at speed, however the track is not moving. Occasionally the belt will move for just a moment then it stops.


do you hear the motor running but the belt is not? if it is the belt need tightened or the drive belt may have broken. remove the motor hood to inspect

Aug 23, 2012 | NordicTrack Exercise & Fitness

1 Answer

My nordictrack is stuck on a program &wont let u do anything else..cant change the speed or incline &the fans wont turn on..its like the consol is frozen or stuck on a program..how can i reset it...


How to Troubleshoot a Nordic Track C2500 X15616db0-ef56-4f0a-afbd-b1ae3379f47f.small.jpg Jolie Johnson

Based in Austin, Texas, Jolie Johnson has been in the fitness industry for over 12 years and has been writing fitness-related articles since 2008 for various websites. She received her Bachelor of Arts in English and philosophy from the University of Illinois.
By Jolie Johnson, eHow Contributor

updated April 15, 2011

Related Searches:

The NordicTrack is a treadmill designed for in-home use. It offers a speed range of 0 to 10 mph and an incline range of 0 to 10 percent. It folds up vertically to save space when you aren't working out and can be rolled to a different room. The console has 16 preset workout programs and features iFit interactive technology. If you have problems with the console or walking belt, you can often fix them yourself with some basic troubleshooting steps
Instructions

  1. Power Turns Off When You're Using the Treadmill
    • 1 Check the reset switch on the bottom of the treadmill near the power cord. If it has tripped, the top of the switch will protrude. Wait 5 minutes then press the switch.
    • 2 Check that the power cord is plugged in completely. If it is plugged in, unplug it, wait 5 minutes then plug it back in.
    • 3 Remove the magnetic key from the console then reinsert it.
    The Console Won't Turn Off
    • 1 Insert the magnetic key into the console. Your C2500 is stuck in demo mode if the console won't turn off after you remove the magnetic key from the console.
    • 2 Hold the "Stop" button down for a few seconds.
    • 3 Press the "Speed" down (-) button. Remove the magnetic key.
    The Incline Does Not Change Correctly
    • 1 Press and hold the "Stop" and the "Speed" up (+) button. While holding the buttons, insert the key into the console, then release the buttons.
    • 2 Press either the "Incline" up or down arrow button. Wait while the incline raises and lowers. This recalibrates the incline system.
    • 3 Remove the key from the console.
    Walking Belt Slows
    • 1 Unplug your C2500 and remove the key from the console.
    • 2 Turn both rear adjustment bolts, located on the back of the walking deck, to the left, a 1/4 turn.
    • 3 Lift the edge of the walking belt in the middle of the deck. You should be able to lift it 2 to 3 inches off the walking platform. If the belt is still too tight, loosen the bolts another 1/4 turn each.
    • 4 Plug the treadmill in and reinsert the console key. Walk on the belt at a slow speed to see if it still slows. Repeat Step 2 if necessary.

Sep 27, 2011 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

My Nordictrack treadmill seems to be stuck. The incline goes up and down and I can't seem to end the problem with the programing. What do I do?


it is trying to calibrate itself, let it go the whole way up and then down without interrupting it. Then it should be fine.

Aug 04, 2010 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

Incline goes up and down


I had the SAME problem, several time, with my NordicTrack A2250 Treadmill.
Allow it to go fully up and then fully down several times, without turning it off. IT seems to "cycle" that way 3 times and then "reboots" itself and starts working normally, again.
I had to figure this out myself... none of the suggestions I read worked.

Apr 24, 2010 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

I have a NordicTrack A2250, about 2 years old. When it's turned on, the control panel lights up, and when I insert a program chip, the console "speaks". However, the neither the incline nor the belt...


Will the treadmill work when the chip is not plugged in, or does it just beep every time you select a button? If so, your problem is easy to solve. The board that supports the two adjacent up and down buttons has slipped. To fix, you'll need to remove the panel and remove the 3-inch retaining bar which is held in my two screws. Realign the board so the buttons are free to move in the available slots. Good luck.

Dec 05, 2009 | Nordic Track NordicTrack Treadmill, A2550

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top NordicTrack Exercise & Fitness Experts

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

Kardoc

Level 3 Expert

4537 Answers

Are you a NordicTrack Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...