Question about Pride Health & Beauty

Open Question

Trying to find an answer for how to remove a rear wheel on a pride victory 10 mobility scooter. Want to replace them. Any help you can give is greatly appreciated.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 118 Answers

SOURCE: Pride victory mobility scooter

18bc1b5.jpg
1. Remove the four screws on the outside perimeter of the console base.
2. Lift off console top cover and disconnect the front-to-back cable.
3. Remove the throttle lever from the throttle pot.
Remove the four screws holding the console base to the mounting plate.

Posted on Nov 27, 2008

Ad
  • 1 Answer

SOURCE: pride victory Scooter battery charged won't run

Its probably too late to give my opinion, but here goes anyway.
I had a similar problem with my mothers scooter and it turned out to be a faulty connection on the wires leading to the motor. I simply pulled the plastic connection apart, cleaned and lubricated the contacts, refitted the connection and all was well.

Posted on May 13, 2009

  • 175 Answers

SOURCE: THE SCOOTER MAKES A HIGH PITCH NOISE WHEN THE KEY IS TURNED ON

The buzzer is a piezo-electric device that is the "horn" for the scooter. It also will alert when the scooter is in reverse, if this option is programmed into the scooter. It receives its power from the PC board or console board which is located inside the top of the shroud at the tiller, where the thumb paddles that direct the scooter are located. If liquids have reached the board, or if condensation has affected the board, the circuit that controls the buzzer may have shorted causing it to come on constantly.

Opening the top of the shroud is fairly simple. Remove about 6 screws holding the clamshell cover together, remove the speed adjust knob, and it should come apart. Inside you'll see a PC (printed circuit) board, green in color with lots of small electronic parts embedded on it. The buzzer is also inside, usually about the size of a marshmallow and black in color with tiny holes to let the noise escape. There will be two wires leading from the buzzer to the plug-in at the PC board. Unplug the buzzer and the noise will stop, but you won't have use of the "horn" at all. Replacing the PC board can be done by a certified Pride tech, but it will probably cost you about $150.00 for parts and labor.

Hope this helps.

Posted on Jul 07, 2009

  • 175 Answers

SOURCE: I have no manual for my Pride victory mobility scooter

http://www.pridemobility.com/pdf/owners_manuals/US_Scooter/US_Victory_10_om.pdf

Click on this link and a pdf manual for a Victory 10 will appear.

Posted on Aug 28, 2009

  • 177 Answers

SOURCE: Pride Celebrity Deluxe Mobility Scooter - Serial Number

Hi. The serial number will be on a sticker on the upright support that holds up the seat. You will have to lift of the seat, and take the cover off the batteries to see it. It should be on the front of the deat support. Neil.

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Scooter is saying error code 8 which is motor does anyone know what this could be please?


Pride Mobility Products Victory 9 Scooter 4 Wheel Error code

www.fixya.com > ... > Pride Mobility Products Victory 9 Scooter 4 Wheel
Pride Mobility Products Victory 9 Scooter 4 Wheel, error code related issues. ... Question about Thermometer Mobility Scooters ... error code is 8 Error code 8 means an internal controller error or problem and requires replacement of the controller. ... Theysay there is no listing for code 9 I have replaced the batteries,checked .
Basic Troubleshooting Instructions - Pride Mobility Productswww.pridemobility.com > Resource CenterPride MobilityScooters. INFINFB2040 Sonic Troubleshooting ... Chargers. INFINFB2586 Charger Indicator Codes ... Disclosure Statement Pursuant to Cal. Civ. Code 1714.43(a)[PDF]Legend Owner's Manual - Pride Mobility Products

Nov 28, 2015 | Pride Health & Beauty

1 Answer

What does the 7 beep code mean on my Pride Victory 10 scooter mean when I turn the key on ?


This is a speed pot or throttle control problem (wig-wag) have you had some speed issues with the scooter before this happened, if so the wig-wag needs replacing. Make sure it is in the centre position at rest and switch the scooter on again.

Jul 11, 2014 | Pride Mobility Products Pride Victory 10 -...

1 Answer

Squeaking axles


It's almost certainly a slightly binding brake, it often happens, especially if you have a sticky hand brake cable/ leaver. I've posted a full answer here as another Pride post.

Jun 10, 2014 | Pride New Mobility Victory XL 4 Wheel...

1 Answer

1997 PRIDE VICTORY GIVEN TO ME, BUT NEEDED FRESH BATTERIES PURCHASED NEW BATTERIES INSTALLED THE KEY, LITES & HORN WORK BUT UNIT WILL NOT MOVE FORWARD AND/OR BACK


check the freewheel lever on th rear of the chair near the right rear wheel if you can push the scooter easily then you are in freewheel locate the lever and move it to the drive mode and try to drive the scooter again if it still won't move then you have other problems that can only be checked by a service tech Hope this helps

Feb 26, 2011 | Pride Mobility Products Pride Mobility...

1 Answer

Pride victory 10 clicks while going foward


If the click is coming from one side of the rear of the scooter, I would think you have a dry axle. If this is the case, you will hear a regular clicking noise, just as if there is a stone in the tyre. All you have to do is remove the wheel, apply some grease to the axle and re-fit the wheel again. When removing the wheel, be careful not to loose the hub key (usually a small strip of square metal that fits in a groove in the axle and wheel). This clicking noise is a very common problem with Pride scooters and one we regularly deal with, even on brand new scooters. If this doesnt cure your problem there are a number of other things it could be, but i would need more specific details to try and help you. Hopefully its just the axle! Hope I have been of some help to you.

Mar 22, 2010 | Pride Mobility Products Pride Victory 10 -...

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pride Health & Beauty Experts

Rob Hill
Rob Hill

Level 3 Expert

1367 Answers

Marvin
Marvin

Level 3 Expert

84540 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Pride Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...