Question about Roland GX-300 CAMM-1 Pro Vinyl Cutter

Open Question

Roland Camm-1 Pro is giving Motor Error 2 in the middle of cutting. What does this error mean and how do i remedy it? All the wires are connected securely between cutter and computer.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
marked
  • 6487 Answers

SOURCE: Roland Camm-1 CX-24 Error Er15:RS-232Err How

Where and when do you see this error? and what operating system are you using?

Posted on Aug 02, 2008

Ad
  • 1 Answer

SOURCE: I have a Roland Camm-1

connect the printer and the comp. and boot up....windows should recognize the new device.
did you add the plotter to "add printers" and its driver and to the correct port?
make sure your plotter is on and loaded and function key pressed.
also some cable manufacturers supply a driver...so download one if need be.
what software are you using? is the software cutter driver set to the correct printer and port?
(by default it never is)!!

Posted on Apr 16, 2009

maxtreadmill
  • 832 Answers

SOURCE: asi image pro 2 treadmill error code 2

Loss signal or No Speed: 3 possible areas that can be causing the problem speed sensor , motor control Board ( MCB ) or the drive motor. Unplug unit remove motor shroud then plug in unit now on the MCB their should be L E D s lights should be on. One of the L E D s should speed on other P W M . Start your treadmill you see the PWM light flickering thus the upper console and cable connections are good now it will go back L S. Reset your treadmill then manually start pushing the running belt2_bing.gif now the speed light should be flickering if it does then the peed sensor is good if not flickering then replace sensor. If we have a good speed sensor then I would check the Drive Motor this done unplugging the unit the disconnect the two leads coming from the motor to MCB then by using a fully charge 18v drill battery connecting the leads to the motor should move it at approx; 1 mph then Your MCB is defective and need to be replaced. if no belt movement you for the most part will have worn brushes or open windings in the motor , I would open the brush compartment and inspect the brushes if they are less than 3/8" in length replace them this should the motor issue. Good Luck

Posted on May 15, 2010

  • 1 Answer

SOURCE: all four colors wont print roland sp300v

you print head is dry out. Normally, it happened on Magenta and Cyan colors.

Posted on Jun 15, 2010

  • 1140 Answers

SOURCE: Roland e09 read "midi error" when connected with

If you have the version 1 cable you need to download a driver. The details are at this link:http://www.cme-pro.com/en/news-detail.php?news_id=105

Posted on Nov 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fault motor voltage error


Check the voltage. You may have to do a hookup. (hookup) a unique connection to a component to check voltage or signals.

May 09, 2014 | Roland GX-300 CAMM-1 Pro Vinyl Cutter

2 Answers

Roland Camm-1 CX-24 Error Er15:RS-232Err How do I fix this? Thanks John


Hi,
Could you let us know when this error pops up. and what all you have tried


Thanks
proton

Aug 02, 2008 | Computers & Internet

1 Answer

Roland drivers


ask them ,,, i think you use the adobe software provided ,

Mar 29, 2014 | Computers & Internet

1 Answer

Pen mode light blinking


Material not aligned or wrong thickness... Blinking means something is not right. Try taking the material out and see if it changes, things like that, troubleshooting....

Nov 26, 2013 | Roland GX-300 CAMM-1 Pro Vinyl Cutter

1 Answer

Message error moteur (02) sur camm 1 GX 300


XEROX 5020 PHOTOCOPIEUSE ERREUR U4 LA SOLUTION

Sep 16, 2012 | Roland GX-300 CAMM-1 Pro Vinyl Cutter

1 Answer

How to get out of dpics mode on a roland camm-1 pro gx400


Please help us the error code comes "dpics mode" in roland gx-500

Jul 29, 2012 | Roland GX-400 CAMM-1 Pro Vinyl Cutter

5 Answers

I have a Roland Camm-1 CX-24 cutting machine that has a parallel connection. I have recently bought a Dell Inspiron 1720 with a Windows Vista OS. I have a USB to Parallel cable to connect the two. I have...


connect the printer and the comp. and boot up....windows should recognize the new device.
did you add the plotter to "add printers" and its driver and to the correct port?
make sure your plotter is on and loaded and function key pressed.
also some cable manufacturers supply a driver...so download one if need be.
what software are you using? is the software cutter driver set to the correct printer and port?
(by default it never is)!!

Aug 03, 2008 | Computers & Internet

Not finding what you are looking for?
Roland GX-300 CAMM-1 Pro Vinyl Cutter Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Roland Office Equipment & Supplies Experts

JonSnell Electronic
JonSnell Electronic

Level 3 Expert

29390 Answers

Ravi

Level 3 Expert

1682 Answers

Are you a Roland Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...