I changed my filter but the message order filter kit keeps blinking when finished why?

some models blink so they keep time that way but if it doesn't change you haven't finished settings

Hi Dee Dee, you have a very messy job ahead of you, in Australia GM did away with drain plugs in the transmissions, Start with a service kit, this is a sump gasket and oil filter, you have to loosen the sump bolts starting from 1 corner, allow 1 corner or the sump to come down this will control where the oil comes out of the sump making it easier to catch the old oil, less mess, when oil is finished draining remove the remaining bolts and remove pan, At this point it is advisable to change the filter (hence the kit) because you must replace the sump gasket

Turn to filter & enter to reset filter.

After replacing the photoconductor kit, you will need to reset the photoconductor page count. Here's the link for instructions on how to reset the page count: http://bit.ly/agYtVo . Or simply press and hold the CANCEL button while the printer is on and the front cover open until all lights are flashing. Hope this helps. If you need more assistance, leave a comment and I'll get back to it. Thanks.

Dear

This problem you will be noticed when toner is 90% empty.
Does the printer is functioning or No. If yes the problem is 90% toner is finished.[10% toner remaining alert]
If printer is not functioning Please change the toner from Genuine dealer. Else your printer fails due to non genuine and refilled toner.

Their's a sensor that the Plug from the Finisher to the copier is not read, first make sure the "Attachment Kit' thats the part where when you push the Finisher to the Copier it Locks, their is a metal tab that sticks out and hits a "Sensor" if it doesn't hit the sensor it will keep telling you attach finsiher or close cover, if it's too annoying you can remove the finisher and unplug it from the rear. On the cover thier are alos sensors that need to be activated by tabs,MAKE SURE these are not missing if you do you need to order these items from "Koycera-Mita" Check those sensors

I have been repairing Makita handtools for many years and generally order parts from two sources.
If I have the breakdown and know the part/kit number I will call Makita at 1-800-462 5482. A live person will help you with your purchase. Other times I order from www.toolpartsdirect.com. Tool parts direct has parts lists and prices for many brands and is easy and convenient if you pay with credit card. Nothing prevents you from looking up a part at toolparts and pricing that part thru Makita. If you are a business may I suggest opening a commercial account at toolpartsdirect to qualify for a generous discount. I rarely order a repair kit favoring replacing only the necessary part to save money. However, sometimes the custmer wants to completely rebuild the tool; since the customer rules, a kit is the best way to satisfy. Good luck.

http://www.chsinteractive.co.uk/pdf_data/KT02.pdf

Order Code….. KT02
POWER SUPPLY REPAIR KIT
BUSH MAXIM 1157 1154 Medion
Goodmans (Standard) 04TA069I 05TA71B 05TA071C
A standard power supply repair kit for faults attributed to the standby +5v rail.
BUSH IDLCD27TV006.
MAXIM 1154, 1157.
MEDION MD30112.
GOODMANS IDLCD27TV006.
The numbers off the boards will read: 04TA069I 26” 27” 30” 32”
& 05TA71B, 05TA071C.
LCD TV POWER SUPPLY PROFILO-TELRA.
Please check the primary of TR20 before fitting the kit.
Primary windings should read approx 2.700mH / 4.00 Ohm.
We recommend all kits are fitted by qualified engineers
We accept no responsibility for loss, injury or damage caused by your use of this kit as a successful repair
depends on your own skill and fault finding ability.


Circuit Reference
Loc Description
F300 T3.15A FUSE
IC21 FSD200
IC30 ICE1QS01
D315 12V ZENER
D318 2V4 ZENER
Q300 BC337
Q302 BC848C SMD
D325 1N4007
C213 33UF
C322 47UF
C356 47UF
C330 1000UF
LINK (IF NEEDED)

continuous blinking green light indicates that the capacitors have failed on the DM pwb. You need the V26 DLP DM repair kit which is available at the following link under their repair category.
http://servicemanuals.vstore.ca/

For the message to be cleared you should enter the service menu and reset the replaced elements