Question about Frigidaire ATF6000ES Front Load Washer

1 Answer

Atf6000es Replaced door lock took out the motor and spins freely no drag, checking brushes and relay next. However before it stopped spinning i heard a loud pop. where would that pop noise come from?

Also with all the testing i now have standing water in the washer. how do i drain it without laying the hose down on the ground?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 78 Answers

I would check the water pump under the unit

Posted on Apr 01, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Door Lock Clicks/Makes noises Washer does not agitate/spin

Sounds like very worn motor brushes to me, as its trying to turn the drum but has'nt the power needed to maintain any momentum,and the blinking door light is because of the bad cotact from brushes to motor.About £20 for a set of brushes or get an engineer to fit new brushes,but get a price first.

Posted on Apr 19, 2007

  • 3 Answers

SOURCE: whirlpool super capacity Lsq9549lw0 has trouble spinning on its own.

If the washer does fine thru the agitation cycle (the washing), that means the motor is OK and the coupler is OK.  It would not agitate unless both are OK.  (and don't listen if anyone tells you the lid switch is bad -- machine would not fill & go thru wash cyle). The spin is another matter.  There is a separate tube for spinning the basket.  There is a drive  block at top of the tube (that sometimes fails)  and there is a separate cluch mechanism below, under the tub.  Those places is where you should look.

Posted on Jul 10, 2008

  • 1550 Answers

SOURCE: Fisher Paykel GWL10US Washer won't spin

It looks like it has to be the control module.
You need to replace it .
It will cost you around $200 .

Posted on Oct 16, 2008

  • 22 Answers

SOURCE: Fisher Paykel GWL10US Washer won't spin

Look at my issue on "eco smart won't drain, smells hot". You could have same issue and your motor just hasn't burned up yet.

Posted on Oct 20, 2008

  • 135 Answers

SOURCE: buzzing - will not spin or drain water

This noise is probably the pump trying to start but will most likely be obstructed.Drain the machine manually by lowering the drain hose into a bucket or bowl and then remove blockage.

Posted on Nov 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ATF6000ES frigidaire will not spin all the time only sometimes


Mine would only spin on the fast final cycle. Wouldn't spin during any of the agitate cycles. I replaced the motor, the speed controller and the main control unit. Nothing fixed the problem. Btw, the door lock worked properly. Had to replace the washer. Sorry, I know this doesn't help.

May 28, 2014 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Bosch washer won't agitate or spin


brushes are spring loaded you take your motor out of the machine and replace them your machine will work

Jan 06, 2014 | Bosch WFVC3300UC 300 Series Vision Front...

1 Answer

After about 5 minutes the unit stops working. No sound or even a fan noise. I just cleaned the filter to see if that helps, but it didn't.


Is the fan running and stopping before the unit completely quits?
If the fan quits the compressor won't run very long.
I would start with the fan motor or capacitor.
Shut the power off to the unit, spin the blower wheel to see if it spins freely. If it doesn't spin freely, (there appears to be a little drag when you spin it),the bearings are bad, if it does spin freely, then try moving the motor shaft from side to side if there’s any play in the shaft side to side then the bearings are worn and motor needs replaced. Then, check the capacitor, if it’s bulging even slightly, the capacitor is bad and needs replaced. Most of the time people replace the capacitor if motor seems ok. If capacitor is ok, turn power on to see if the motor is getting the proper voltage, if it is and not trying to run, then the windings are probably open, the motor's bad and needs replaced.
r.

Aug 21, 2009 | Dehumidifiers

1 Answer

Motor and fan fails to come on


Shut the power off to the unit, spin the fan blade to see if it spins freely. If it doesn't spin freely, (there appears to be a little drag when you spin it),the bearings are bad, if it does spin freely, then try moving the motor shaft from side to side if there’s any play in the shaft side to side then the bearings are worn and motor needs replaced. Then, check the capacitor, if it’s bulging even slightly, the capacitor is bad and needs replaced. Most of the time people replace the capacitor if motor seems ok. If capacitor is ok, turn power on to see if the motor is getting the proper voltage, if it is and not trying to run, then the windings are probably open, the motor's bad and needs replaced.

Aug 15, 2009 | Ruud Matching Split Air Conditioner

1 Answer

Duo Therm kicking on the compressor, getting cold, but no fan!


Shut the power off to the unit, spin the fan blade to see if it spins freely. If it doesn't spin freely, (there appears to be a little drag when you spin it),the bearings are bad, if it does spin freely, then try moving the motor shaft from side to side if there’s any play in the shaft side to side then the bearings are worn and motor needs replaced. Then, check the capacitor, if it’s bulging even slightly, the capacitor is bad and needs replaced. Most of the time people replace the capacitor if motor seems ok. If capacitor is ok, turn power on to see if the motor is getting the proper voltage, if it is and not trying to run, then the windings are probably open, the motor's bad and needs replaced.

Aug 12, 2009 | Dometic Rooftop RV Air Conditioner

1 Answer

Fan on unit not running


Shut the power off to the unit, spin the fan blade to see if it spins freely. If it doesn't spin freely, (there appears to be a little drag when you spin it),the bearings are bad, if it does spin freely, then try moving the motor shaft from side to side if there’s any play in the shaft side to side then the bearings are worn and motor needs replaced. Then, check the capacitor, if it’s bulging even slightly, the capacitor is bad and needs replaced. Most of the time people replace the capacitor if motor seems ok. If capacitor is ok, turn power on to see if the motor is getting the proper voltage, if it is and not trying to run, then the windings are probably open, the motor's bad and needs replaced.

Aug 09, 2009 | Heating & Cooling

1 Answer

Fan not working


Shut the power off to the unit, spin the fan blade to see if it spins freely. If it doesn't spin freely, (there appears to be a little drag when you spin it),the bearings are bad, if it does spin freely, then try moving the motor shaft from side to side if there’s any play in the shaft side to side then the bearings are worn and motor needs replaced. Then, check the capacitor, if it’s bulging even slightly, the capacitor is bad and needs replaced. Most of the time people replace the capacitor if motor seems ok. If capacitor is ok, turn power on to see if the motor is getting the proper voltage, if it is and not trying to run, then the windings are probably open, the motor's bad and needs replaced.

Jul 31, 2009 | Fedders A7DH65B2A Dehumidifier

5 Answers

Front loader will not spin


The problem is the door latch assembly. You can get it at your local parts supplier or oder it through repairclinic.com. Should cost $50-$55. My hubby is replacing mine now. Not an easy part to replace, but by all information I have gathered from the manufacturer and the parts department, this is a common problem and most likely the cause of the machine not spinning. It runs through all the rest of the cycles, but will not spin, even on spin only cycle. The good news... if you replace the door latch assembly once, the replacement part is much stronger than the original and shouldn't have to be replaced again.

Jan 14, 2008 | Frigidaire ATF6000ES Front Load Washer

4 Answers

Washer wont spin. BUT, DOOR IS LOCKED. MAH 4000


Solution is right ...its your MCU Easy repair.
~Baloo

May 06, 2007 | Maytag Neptune MAH5500B Front Load Washer

Not finding what you are looking for?
Frigidaire ATF6000ES Front Load Washer Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1479 Answers

J. Bradshaw

Level 2 Expert

121 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...