Turn off alarm in XC-0366 - Measuring Tools & Sensors

Your 'figure'??

Normally it has to be done in order. Remove both lots of batteries. Put the base unit batteries in first and then put in the outside unit batteries. they should pair. In fact the manual states that.

Instructions:
- Open the battery compartment on the weather station and insert 2 x AA
batteries, taking care to put them in the correct polarity. Close the battery
compartment.
- Open the battery compartment on the transmitter and insert 2 x AA batteries,
taking care to put them in the correct polarity. Close the battery
compartment.
Note: Ensure to install the batteries into the weather station and transmitter
within the same hour to ensure that they synchronize properly.

DigiTech XC-0366 User Manual - ManualsLib

https://www.manualslib.com > ... > Weather Station

View and Download DigiTech XC-0366 user manual online. Wireless Weather Station With Outdoor Sensor. XC-0366 weather station pdf manual download.

Page 6 of the manual refers

DIGITECH XC-0366 USER MANUAL Pdf Download ...

www.manualslib.com > ... > Weather Station

Temperature Alert Setting: You can program your weather station to sound an alert whenever the outdoor temperature exceeds the upper or lower pre-set limit.

It is triggered by mileage driven.

This desktop computer does not have wireless built-in.

See manual global download acer com

Pressing the - (minus) button on the back toggles temperature units. Pressing + (plus) toggles barometric pressure units.

0366 783 4480 / 783 0366 4480 / 03664484783

buy new car

Retirer les cartouches du produit.
afficher sur le panneau de contr?le. " xc="1.Wait for the 'Insert Cartridges ' message to display on the control panel." closure_uid_u4snr0="101">1.Wait pour le message "Ins?rer les cartouches" pour afficher sur le panneau de contr?le.
produit. " Xc="1.Disconnect the power cord from the back of the product." closure_uid_u4snr0="102">2.D?connectez le cordon d'alimentation de l'arri?re du produit.
secondes. " Xc="1.Wait 60 seconds." closure_uid_u4snr0="103">3.Attendre 60 secondes.
4.Rebranchez le cordon d'alimentation. produit n'est pas automatiquement en marche, appuyez sur le bouton Power (). " Xc="If the product does not automatically turn on, press the Power button ( )." closure_uid_u4snr0="105">Si le produit n'est pas automatiquement en marche, appuyez sur le bouton Power ().
cartouches, puis fermez toutes les portes ouvertes sur le produit. " Xc="1.Reinsert the cartridges, and then close any open doors on the product." closure_uid_u4snr0="106">5.R?ins?rer les cartouches, puis fermez toutes les portes ouvertes sur le produit.
vous recevez une invite pour imprimer une page d'?talonnage, le faire. " Xc="1.If you receive a prompt to print a calibration page, do so." closure_uid_u4snr0="107">6.Si vous recevez une invite pour imprimer une page d'?talonnage, le faire.
USB ? l'arri?re du produit, puis relancez l'impression." Xc="1.Reconnect the USB cable to the rear of the product, and then try printing again." closure_uid_u4snr0="108" >7.Rebranchezt le c?ble USB ? l'arri?re du produit, puis relancez l'impression. si>vous avez suivi toutes les ?tapes ?num?r?es ci-dessus et connaissent encore un probl?me, le service du produit

Could be the belt if it has one. If not then your problem could be as simple as a pin broken in the tine shaft. There is also a pin in a gear in the gear box also, This will require shop work.

good luck.