Question about Frigidaire Kitchen Ranges
This is going to require a new EOC, which is the control board. I attached a link that may help.
Posted on Feb 09, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
"PF" indicates the electronic control detected a Power Failure.
This could have been caused a brief power outage OR may be an indication that the connections to the oven, either at the stove or at the plug are loose.
Posted on Jun 10, 2008
Call the manufacturer. Chances are it's a common problem and they already know about it.
Posted on Nov 04, 2008
The last expert is correct.
According to the Frigidaire technical documentation, most likely the cause of the problem is a bad Electronic Oven Control (EOC).
Check the wire harness and the P4 connector at the EOC. If the wire harness and the connector are fine, replace the EOC
You could try to disconnect the power supply for few minutes, say 15 minutes and see, if that could help the situation unless you need to replace EOC/Clock/Control board.
I don't think it is sensor as this is a common problem on these units and 99% it is faulty EOC.
Let me know,if needed further assistance.
Note - Kindly perform the repair, if you have prior appliance repair experience. These ovens are quite dangerous to work. It could not only damage the oven but could also harm you,if done in an appropriate way.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
Posted on Dec 18, 2010
Tips for a great answer:
Good Afternoon friend, thank you for your post!
I see that you are having some difficulty with your Frigidaire range displaying a 2:30 and cutting off. This sounds like a wiring issue or a control panel problem within your range. I would recommend performing a reset and you can do that by disconnecting power to your range by flipping the household circuit breaker and leaving it off for roughly ten minutes. If that does not help to resolve the issue I would suggest having a professional technician come out and accurately diagnosis your range. Best of luck! -Matt
Feb 13, 2015 | Frigidaire Kitchen Ranges
I appreciate the post, dan moore!
From the information you have provided your Frigidaire range is displaying an "F11" error code. Typically, the "F11" error code stands for a shorted keypad. This could be a false error code and the best way to clear any false error codes is to disconnect power from the range for at least ten minutes. If you continue to get an "F11" error code you may need to replace your EOC (Electronic Oven Control), I would recommend having a professional technician come out to properly replace any electrical component to avoid personal injury. Hope this information is helpful to some degree. -Matt
Dec 14, 2014 | Frigidaire Kitchen Ranges
Hello friend, thank you for your post!
Based off the information you have provided, I understand that your Frigidaire dryer is displaying an "E52" code and the dryer will not start. Typically an "E52" code stands for motor fault, I would attempt to perform a reset on your appliance by disconnecting power for roughly ten minutes. After the reset if you are still receiving the error code I would recommend having a professional come out to diagnose and repair the appliance. Best of luck. -Matt
Aug 06, 2014 | Frigidaire Affinity Series FASE7073LA...
Aug 02, 2013 | Frigidaire Kitchen Ranges
Oct 30, 2012 | Frigidaire 30" Self-Cleaning Freestanding...
1. (F11, 12 & 13)
Disconnect power, wait 30 seconds and reapply power.
2. (F11, 12 & 13) If fault returns upon power-up, replace EOC.
EOC = Electric Oven Controller
Jun 13, 2011 | Frigidaire PLES399EC Electric Kitchen...
Dec 16, 2008 | Frigidaire FEF366 Electric Kitchen Range
Dec 16, 2008 | Frigidaire 30" Self-Cleaning Slide-In...
118 people viewed this question
Usually answered in minutes!