Error c-1106 for finisher 537SD how do i clear it

http://computerfixerpeople.com/sony-bravia-error-code-1106.php

http://community.sony.com/t5/Internet-TV/error-code-1106/td-p/43857

Have a read of this

0106 refers to a map sensor or manifold absolute pressure.,0122 refers to tps or throttle position sensor,1106 is an itermittent problems,1122 is a low volt or cicuit ..1599 chech for idle fluctuatin... you must check the all faults to clear the the PCM error..

Error 1106 is an indication that the Domain Name System (DNS) was unable to resolve. Follow the steps to check the Internet connection: 1. Check the Network Connection. 1. Using the supplied remote, press the Home or Menu button. 2. Select Network Setup . 3. Select View Network Status . 4. Select Check Connection . If any of the connection settings fail, verify that the TV is properly connected to an active Internet connection. Follow these steps, if the error continues to appear: 2. Unplug the TV and wait 60 seconds. 3. Power on and off all of the networking equipment, including the modem and router. 4. Allow the Networking equipment to reset after powering them of and on. Test that the connection is active by using a computer. 5. If the issue continues, wait and try viewing the content later.

Ethernet connections between the tv and the computer into one signal frequencies are not compatible signals.Ur main home computer have internet service connection go through a wire or wire less Router for a internet signal through out the house.Connect the tv internet signal through the Router.Internet signal will work fine.

Error 1106 is an indication that the Domain Name System (DNS) was unable to resolve. Follow the steps to check the Internet connection:

1. Check the Network Connection.
   1. Using the supplied remote, press the Home or Menu button.
   2. Select Network Setup .
   3. Select View Network Status .
   4. Select Check Connection .
   If any of the connection settings fail, verify that the TV is properly connected to an active Internet connection.
   Follow these steps, if the error continues to appear:
   
2. Unplug the TV and wait 60 seconds.
3. Power on and off all of the networking equipment, including the modem and router.
4. Allow the Networking equipment to reset after powering them of and on. Test that the connection is active by using a computer.
5. If the issue continues, wait and try viewing the content later.

Solution proposed by Soufane (member of the Fixya community) :

Rank: Wiz

Rating: 99.31%, 51 votes

Error 1106 is an indication that the Domain Name System (DNS) was unable to resolve. Follow the steps to check the Internet connection:

1. Check the Network Connection.
   1. Using the supplied remote, press the Home or Menu button.
   2. Select Network Setup .
   3. Select View Network Status .
   4. Select Check Connection .
   If any of the connection settings fail, verify that the TV is properly connected to an active Internet connection.
   Follow these steps, if the error continues to appear:
   
2. Unplug the TV and wait 60 seconds.
3. Power on and off all of the networking equipment, including the modem and router.
4. Allow the Networking equipment to reset after powering them of and on. Test that the connection is active by using a computer.
5. If the issue continues, wait and try viewing the content later.

sounds like the DC controller and or the Finisher controller have gone bad. Unfortunatly there is no easy fix for this problem. you will need to get someone out to have them checked but if you leave the finisher off of the copier it should still work so at least you can make the copies.

When trying to authorize the computer or the Reader digital book to the Reader Library software, you may get an error such as 2027, 1106, 2029, 2056. Follow this procedure to resolve this issue.

Make sure you the firmware of the Reader digital book is current. Firmware updates are available online through the Drivers & Software link on this page.
Disconnect the Reader digital book from the computer.
Do not unplug the Reader digital book while it is updating.

Close the Reader (eBook) Library software.
Connect the Reader digital book to the computer and turn it on.
Open the Reader (eBook) Library software.
If the error still occurs, proceed with the steps below:

First, please connect the Reader to the Computer.
Then, install the Adobe Digital Editions software. Use the installer at http://www.adobe.com/products/digitaleditions .
Setup Assistant will be displayed in the Adobe Digital Editions program.
Please let me know when you finish installing the Adobe Digital Editions software.
Now, please click the Authorize button and then the Finished button.
Reopen the Reader Library.
Go to the Reader Store and sign in.
You will now be able to download an eBook and transfer it to the Reader device.