How do I access my voice mail remotely? (talkswitch ts200)

You have to contact your telco for instructions if messages are held on their servers as they vary. If it is your own voice mail phone at home, you need to read the manual.

'make model (what it is)' in all questions helps.

If you need the remote access code for the answering system, then the original (default) access code is given in the manual on page 50 (page 53 of the PDF) and on 55 (page 58 of the PDF). See the manual online at https://att.vtp-media.com/ecp/documents/product_Product/364/UserManual/5977/SL82118_manual_i10.pdf . Unfortunately, if the remote access code has been changed, the default code will not work. As far as I know there is no way to reset the SL82318 remote access code to the factory default remotely. See page 50 of the manual to reset the phone's access code when you are using the handset. When you use the handset and start to change the code, the current remote access code will be announced first.

Any voice mail system would be accessed using the phone number and codes from your telephone service provider. This information will not correspond to the answering system of the SL82318.

I hope this helps.

Cindy Wells

Les,

If you want to delete the actual voice mails, you have to go through your phone company (using their keypad commands) since voice mail is only accessible through your phone (but the voice mail messages are stored through your phone company provider).

Info from the Uniden DECT 6.0 6035 Manual:

Using the Voice Mail Service If you subscribe to a voice mail service, you can use your phone to access your voice mailbox. The new message LED on the handset ?ashes and VM appears in the handset display whenever you have messages waiting in yourvoice mailbox. When you subscribe to the service, your voice mail provider provides you with the access number and the required voice mail signaling tone. You can use your phonebook to store the access number.

Resetting the Voice Message Waiting Indicator

When you receive a new voice mail message, the new message LED on the top of the handset ?ashes and
appears in the handset display. In the event your message alert tone gets out of sync with your phone company's voice messaging system, you can reset back to its original "no messages waiting" state. To reset, press and hold [?nd hs] on the base for ?ve seconds. A beep sounds and the message alert tone is reset.

Here is the manual:
Uniden 6035 1 Owner Manual

If you subscribe to a voice mail service, you can use your phone to access your voice mailbox. The new message
LED on the handset flashes and appears in the handset display whenever you have messages waiting in your
voice mailbox. When you subscribe to the service, your voice mail provider provides you with the access number
and the required voice mail signaling tone. You can use your phonebook to store the access number

First try this. When you call your home number, and the voice mail picks up, hit either the * or # key. It might have to be pushed as soon as the voice mail answers or after the beep. Try both. You might have to set up a pin from the voice mail menu from your home phone.

call your phone and once the voice mail picks up hit rhe pound symbol you will have to look up what your phones default voice mail code is but after that you can set a code and check you voicemail using any phone

Log into your Management software.
Go to each phone line.
At the very bottom of the call handling section you should see routing options. Change these setting to the desired number of rings.

Hope this helps you.

Follow the instructions beginning on page 62 of this manual.

When you call in from the outside wait for auto attendant to answer. As soon as the "Thank you for calling" starts, press [*], and your mailbox number. If that does not work you may need to put a [#], 165 before the [*], mail box. This is assuming that most voice mail and auto attendant settings are operational and you have a Panasonic KX-TVS voice mail.
If a live person (not to be confused with the living dead) answers, have them transfer you to voice mail and do the whole [#], 165, [*], your mail box thing.

from a tt phone, after the message, hit * your ext # and then your pswrd.
it's just like retreiving your messages from an ext not your own.

from there you can change your access info in the admin section.
pause 5 secs and listen to the prompts from the vm syst itself.