Question about Makita Drills

Open Question

HOW DO I REMOVE THE CLUTCH ON A MAKITA DSC34 - Makita Drills

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a new Makita DF330DW and the clutch started slipping out of nowhere. The drill will turn in fwd and rev but as soon as there's any resistance, it quits spinning. I have run it through all of...


Definitely a faulty clutch. Take it back to where you bought it (if it was recent), otherwise send it or go to a Makita Service Centre.

Hope that helps

Jul 10, 2011 | Makita DF330DW 108Volt Ultra Compact...

2 Answers

How do you remove the clutch on a makita 8406 have split the body so far ..thanks


How is the clutch removed from the makita 8406 core drill

May 15, 2011 | Makita Drills

1 Answer

How do i remove the drill bit from a Makita 8391d cordless drill


Put the clutch on a high number, put the reverse on, hold the chuck tightly, lightly press the triger. If it does not come undone, make the clutch tighter (loer number).

Jul 17, 2010 | Hand Tools

2 Answers

I have a Makita DCS640120 Commercial Grade 20Inch 64cc and when i turn it on the chain automatically moves how do i fix it to where it will idle till i press the trigger?


Turn the idle speed screw CCW till the chain stops turning at idle, but the engine continues to run. Make sure the carburetor fasteners are tight. Remove the chain cover, bar, and chain. Spin the outer drum of the clutch to check the bearing which lies between the drum and internal components. If it doesn't spin freely, try oiling the drum bearing area and work it into the bearing. If no help, plan on replacing the clutch mechanism. Hope some of this helps!

Jul 12, 2010 | Makita DCS640120 Commercial Grade 20Inch...

1 Answer

My Makita 3.0ah cordless drill does not drive anything when I put pressure on it. Would the clutch be worn and if so is it easy to repair?


Clutch is part of the transmission assy - yes it is about the only thing that it can be causing your issue. It is a fairly inexpensive and easy fix on Makita - the worst part is removing the chuck.

Jun 25, 2010 | Makita 18V 1/2"CRDLS Drill Kit

1 Answer

How to remove chain drive on makita Dcs6401-20?


HI , FIRST UNDO BOTH SIDE COVER BOLTS ON THE CHAIN COVER AFTER MAKING SURE THE CHAINBRAKE IS IN THE OFF POSITION,[BRAKE LEVER PULLED BACK].TAKE THE TWO NUTS OFF REMOVE THE COVER,LIFT THE BAR SLIGHTLY AND PUSH IT TO THE REAR.THAT WILL LOOSEN THE CHAIN SLIP THE CHAIN OFF THE BAR AND REMOVE THE BAR ,ONCE THE BAR IS OUT OF THE WAY ,YOU TAKE THE CHAIN OFF THE SPROCKET BEHIND THE CENTRIFICAL CLUTCH AND SLIP IT OUT AROUND THE BACK. AFTER CLEANING EVERY THING ,PUT IT ALL BACK THE SAME WAY .YOU WILL HAVE TO SCREW THE ADJUSTER BACKIN SO AS TO EASILY FIT THE BAR TO THE ADJUSTER PIN ,IT IS NOT DIFFICULT AND AS YOU SEE THE PARTS IT WILL FALL INTO PLACE

Nov 18, 2009 | Makita DCS6401 20 20",64cc Chainsaw 2...

2 Answers

Can't get clutch plate off of makita 340 dcs


you need a piston stop to stop the engine from rotating,then with a clutch tool you can spin off the clutch,most of them are left had thread.if you don't have a clutch tool you can use a hammer and punch on one of the main arms of the clutch itself.for a piston stop you can use a piece of 1/4"rope.put the piston at the bottom of the stroke and stuff the rope in the sparkplug hole,this stops the piston from reaching it's full stroke.

Oct 20, 2008 | Makita DCS51018 18" 45cc Chain Saw 2 Cycle

1 Answer

My Makita handrill is not working. It's just like loose,and the drill is not rotating anymore.


Your bearings in the Clutch have fallen out of place. 
Basically the tension screws pulling the clutch against the body.
Have became loose. If you Tighten them most likely wont fix it.
You should contact Makita. If you do open the drill. The Clutch assembly will be a task to reassemble. And the warranty might be voided.

Aug 17, 2008 | Makita Tools 18V 1/2" Lxt Lithium - Ion...

Not finding what you are looking for?
Drills Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Makita Drills Experts

John Trevino

Level 3 Expert

1407 Answers

Marvin
Marvin

Level 3 Expert

85160 Answers

Spud Howell

Level 2 Expert

66 Answers

Are you a Makita Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...