Question about Dacor Ovens

Open Question

My Dacor single wall oven PCS130 does not heat the bake element. We've checked and the bake element does not have any voltage when the oven is turned on.

The broiling element works. All indicators work, but no heat. Thanks.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
hotuna
  • 288 Answers

SOURCE: GE Wall Oven - No heat (broil or bake)

On appliances like this only the heating elements use 220 volts. things like the clock, fan, etc use 110 volts. That is why some things work and other do not. Start at the breaker, sometimes a double pole breaker will have 1 side tripped, but will look perfectly fine. switch the breaker all the way to off then re-set. If nothing changes follow the power to the appliance remove the panel and look for some fuses, check to see if any are blown. Also sometimes the microwave will have a separate power source even though its built in to the same appliance. So that's not always a good symptom to follow.

Posted on Nov 11, 2007

Ad
watugot
  • 290 Answers

SOURCE: OLD GE Wall Oven doesn't heat properly

On these older ovens ther is usually always 120 volts on the elements at all times.
If you check across the element ends with it in bake you should read 240V. If not, there is a problem with the control. With the voltage drop you describe, it sounds like you are losing power on one line of voltage coming to the element.
Post back to let me know what you find out or if you have any questions.

Posted on Nov 24, 2007

aborcass
  • 2651 Answers

SOURCE: GE Profile -Installed wall oven - won't heat

brand new??? under a year old??? if so you have a warr call for service, but it sounds like an ignitor isssue, brand new , perhapsgot damaged in shipping 1-800-ge-cares

Posted on Mar 30, 2008

  • 1 Answer

SOURCE: Bake element does not heat

After removing the racks, rack rails and the back plate I removed the 2 screws the hold the bake element. Lifting the front of the bake element up and carefully pulling the element out and gently moving the element so the connector clear the hole I was able to disconnect the wire. After testing for continuity with an ohm meter (non found) I determined the element need to be replaced. $37 and 45 minutes total.

Posted on May 29, 2008

  • 3230 Answers

SOURCE: GE JTP 1580W288 Set oven to Bake, switches to broil at bake temp

The F2 Error code means the oven has detected an excess temperature condition. Most often this is due to a bad temperature sensor - the sensor costs about $75 from an online repair site. 
How to remove and replace the temperature sensor. In most GE ovens, when you open the door, you'll see the rod-shaped temperature sensor sticking out of the back wall at the upper left. It's about six inches long and a bit more than 1/8" in diameter, held in place with two screws. 

Turn off the circuit breaker (built-in ovens) or unplug the range before attempting the replacement. 

The replacement sensor will come with instructions, but basically it's a matter of removing the sensor, pulling out the wires to where they are connected and disconnecting them. You may have to snip. The replacement sensor will come with high-temp wire nuts to hold the new connection. Polarity doesn't matter; it's a straight resistance thermocouple. Hook it up, be sure you poke the connections back far enough so that they're on the other side of the thermal insulation and not resting against the back of the oven. 

If you continue getting the F2 error after replacing the sensor, then the problem is likely in the control module - this is the circuit board behind the keypad and clock. 

You'll need to remove the decorative bezel to get behind the control panel. Remove screws and set off parts in order - it's not complicated. Once the bezel is off there are two more screws that hold the panel in place. Then you can lift the panel up about a half inch and pivot it forward toward you. You'll see a bunch of wires going to a circuit board. 

On the panel you will notice some black plastic boxes that say "Potter & Brumfield" on them. These are relays. Check the relays - slide the black plastic cover straight up to expose the coil and the contacts. The coil, when energized, closes the contacts - look at all the relays. You can manually close the contacts with your finger (be gentle). If the contacts of one of them are stuck, they might be welded together. You can fix the problem by prying apart the welded contacts gently with a knife blade. Take some time to gently polish the relay contacts with a folded bit of fine grain sandpaper - this will get some more life out of them. Be gentle and careful - the relays aren't complicated but if you bend the contact or rip it out, you'll have to replace the controller, which will set you back a couple hundred dollars. If you unstick and burnish the relays, they will probably eventually weld together again as the rough spot will spark, but when you burnish them with sandpaper they should be good for some more life before they need to be replaced. 

If the problem isn't the temp sensor or welded relay contacts then the problem is obviously somewhere else, but temp sensor and relay contacts will account for the lion's share of F2 errors. 

Once again, be safe, be careful, be gentle. Ovens are not very complicated and they're tough, but always exercise care. Always disconnect electricity before messing with them.
good luck,

Posted on Jun 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dacro Wall oven (electric) does not heat past 345 degrees on bake or convection bake but broiler works and bottom oven works fine (for bake, convection bake and broil).


it could be the oven temp sensor rod located near the top of the inside of the oven,or possibly the bake element has a hot spot on the element and can no longer pass enough current thru this spot to correctly heat to your settings a hot spot on the element will look discolored in this area

Jul 28, 2012 | Dacor Ovens

1 Answer

My oven flashes and beeps F 4. What does it mean?


F4 on a Dacor oven is a bad temperature sensor.
The temperature sensor is inside the oven up high on the back wall

Mar 29, 2011 | Dacor PCS130 Preference Electric Single...

1 Answer

My upper oven/ convection function on my dacor ecs230b will not heat


Bake and convection bake settings both use the bottom bake element to heat. It would be unusual for bake to work without conv. bake working. You also have pure convection which uses a different element surrounding the conv. fan on the back of the unit. If you press a feature and nothing happens it's the touch pad. If it comes on then turns back off it's probably the ERC (clock). If it comes on and wont heat only in pure conv. possibly an upper relay board or element problem.

Sep 22, 2009 | Dacor ECS230 Epicure Electric Double Oven

1 Answer

Our Dacor Millennia wall oven will not heat


There is a manual reset button behind the vent under the touch pad. Turn off the power. Open the door. Remove the vent. Behind the latch is a two wire switch. press the red button on it until it clicks. reassemble and turn on power. It over heated when the power went off by stopping the cooling fan.

Mar 04, 2009 | Dacor MCS130SS Millennia Electric Single...

1 Answer

Dacor preference oven


Did you turn off the circuit breaker for 30 mins?

Oct 01, 2008 | Dacor PCS130 Preference Electric Single...

1 Answer

PCS 130 Keypad


Dacor probably won't cover anything. F1 is either the touch pad or ERC (clock). If it stops beeping when the touch pad is uplugged from the ERC then the touch pad is the problem if not it is the ERC. Call Dacor Customer service to get a price on the parts and to voice your displeasure.

May 22, 2008 | Dacor PCS130 Preference Electric Single...

1 Answer

Dacor Oven - convection fan stays on while on "bake" setting


Question: does the unit appear to hold the correct temperature? Most convection units only turn the heating elements on and off...not the fan. If the unit is reporting operating temp and then taking other direction...and it is cooking right...you're done.

Nov 14, 2007 | Dacor ECS127 Epicure Stainless Steel...

Not finding what you are looking for?
Ovens Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dacor Ovens Experts

Tyler T

Level 1 Expert

35 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Jose Pino

Level 3 Expert

563 Answers

Are you a Dacor Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...