How to set the abbreviation of a day on Grundig Sonoclock 410

It sounds like you may be experiencing a configuration issue with your M-Audio FireWire 410 audio interface. Here are a few steps you can try to troubleshoot the issue:

1. Check the connections: Make sure that the FireWire 410 is securely connected to your computer and that all cables are properly plugged in. If the connections are loose or faulty, it can cause problems with the audio output.
2. Restart the device: Sometimes, restarting the audio interface can resolve issues with the audio output. To do this, disconnect the FireWire 410 from your computer, wait a few seconds, and then reconnect it.
3. Update the drivers: It is possible that the drivers for your FireWire 410 may be out of date or incompatible with your operating system. To update the drivers, visit the M-Audio website and download the latest drivers for your device. Once the drivers are installed, restart your computer and try using the FireWire 410 again.
4. Check the settings: Make sure that the FireWire 410 is selected as the default audio device in your operating system's audio settings. You can access these settings by going to Control Panel > Hardware and Sound > Sound. Under the Playback and Recording tabs, select the FireWire 410 and click the Set Default button.

If these steps do not resolve the issue, it is best to contact M-Audio support for further assistance. They should be able to provide you with specific guidance for troubleshooting the problem with your FireWire 410.

Instructions for setting an MSP74810W watch.

Press the "Mode." button three times (the "Mode" button is the one next to the lower left of the dial when facing it).The first time you press you'll see the ST, or stop watch function, the second time you'll see the AL, or alarm function, the third time you'll be back to the time of day function but the seconds will be flashing.

Change the flashing seconds digits to read 00 by pressing the "Start" button (the "Start" is the button next to the upper right of the dial when facing it).

-To advance from the flashing seconds' reading to the hour of the day's digit/digits you press the "Reset" button at the lower right of the dial,
-To advance from the flashing hour digit/digits to the minutes digit/digits you again press the "Reset" button,
-To advance from the flashing minutes digit/digits to the month's digit/digits you again press the "Reset" button,
-To advance from the flashing month's digit/digits
to the day of the month's digit/digits you press "Reset,"
To advance from the flashing day of the month's digit/digits to the day of the week's abbreviation you again press "Reset,"
-To advance from the flashing name of the week's abbreviation back to the seconds' of the minute you again press "Reset," and from there you can go through the cycle again.

While the hour of the day with its A[M] or P[M] designation, the minutes of the hour, the month of the year's number, the day of the month's number, or the abbreviation of the day of the week's name is flashing press the "Start" button once, repeatedly, or hold it down to advance the number or letters to their correct designations.

Once all designations are correct push "Mode" so that none of the numbers or letters are flashing. Your watch is now set.

http://www.grundig-gbs.com/index.php?option=com_docman&task=cat_view&gid=288&Itemid=248&lang=de

1. Press and hold down TIME.
2. Press HOUR briefly to set the hours step by step or hold it down to run through the hours quickly.
3. Press MIN briefly to set the minutes step by step or hold it down to run through the minutes quickly.
4. Release TIME to conclude the settings.

Thanks.
gylacz

Press snooze And keys +or- to set the day

Try formatting the memory - or try using an external memory card (SD).

Ask here:
http://manualfox.com/link/grundig.htm
they can get you every Grundig manual.

hello, I had thesame problem. I tried everything, after 14 days, where was TV off a tried itagain...an the same problem: text " ATS... OK " So a tried hold 3seconds on Grundig driver button "OK" and then the started automatictunnig. After it - averything is function! :)

poop
no format
reset the device google it

Hello Sally,
here is the solution :)


https://dex.grundig.de/GIM/internet/document/GKL0151D.PDF

maybe it doesn´t work try this site and choose

http://www.grundig.de/index.php?id=9

Greets
miieke