No signal my tv / jensen / - Jensen Televison & Video

Jensen 19" 12-Volt TV/DVD - Camping World

www.campingworld.com > ... > TVs & Accessories > TVs

Rating: 2 - ‎2 votes - ‎$269.00 - ‎In stock
Where does one get a replacement remote for the 19 inch /dvd model ??/. 1 answer(s)... Need remote replacement for Jensen JE1911ABC. 1 answer(s).

JENSEN LCD TV Accessories - Jensen RV Direct

www.jensenrvdirect.com > Products > LCD TVs

Items 1 - 12 of 22 - We also offer video control centers, PAL tuners, and digital tuner boxes which will convert your analog TV signal into a digital one.

postheadericon JENSEN JE1914DVDC DVD STAND

dynastre.tk/469748/dvd-jensen-je1914dvdc-stand

It sounds that the optical pickup unit is faulty. Put a disc cleaning disc into the set, and play it once. If the fault is with dust or dirt, it will be cleared out. If not, replace the optical pickup unit.

Hi.
No, your tv is an older model sdtv with an analog only NTSC tuner.

Newer model have an ATSC/Qam digital tuner, but not your model.

This means that if you want to watch tv, you'll have to get a converter box. It will have the ATSC/QAM tuner i it, and it converts the signal into lower definition NTSC, and then sends it to the tv through either coax cable, or rca cables.
Once in a great while you might even find one that has s-video output, but those usually are expensive.

I hope this helps you out.

Try this first to see if the remote is sending out the signals. Testing remote control:
The remote control puts out IR (InfraRed) signal that human eyes cannot see, to find out if the remote is sending out the signal or not you just point the remote at the digital camera's Lens (Digital Camera can detect IR), you should see flashing light on the camera's screen when any one of the remote button is pushed. If you do see the flashing on the camera, then the problem is in the TV IR receiver or the main logic board; more troubleshooting with scope will be needed to look at the signals.

http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
http://www.fixya.com/support/r7406380-tv_training_manuals
Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm/
Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Check RGB signal. Video drive circuit

check the antena wire if it plug to your tv,

Not all units were fitted with the DTV tuner before the switch over occurred. you set should have an insignia that sates that it is DTV ready. if this insignia is not on the box or actual set, you will need a converter box to receive this DTV signal.

Looking at the manual, the specifications indicate that this is an NTSC TV. You would need an ATSC tuner (a digital converter box) to convert the digital signals into the analog ones that this TV can receive. You may also need an antenna designed for DTV signals to get a good reception.

This is the best solution for your problem as a 40 year experience with wires etc. Go to the source of your cable signal connector . Open it and clean the terminals with emery paper , sand the end of the cable shiny clean from corrosion , get a new barrel connectors with gold terminals if possible lengthen the ends of the cable , insert and tighten good, use thick rg-16 or rg 40 cable with good insulation ends crimped professionally with a crimpier or buy ready made , not from dollar store. Get a gold plated professional splitter if you need one or two , it will cost about 15 or more each . Make the cable runs as short as possible, using the thick good cables. If needed get a signal magnifier. From radio shack or the source etc. Connect them good and tight . Ground the splitters . Problem solved , you will get crystal clear channel 2 to 7 including 3 and 4 . Isolate the TV cable from other cables and power wires. Vitally

I have the Jensen head unit. I found out a while ago that the 6th Gen Ipod Classic does not send video through the multi-pin connection. Only out of the headphone/A/V out. This is the reason it does not work via the JLink cable into the Jensen VM9312