Question about Generac Electrical Supplies

1 Answer

I have a red light and message Stopped-Alarm Overcrank. what could be done

Generac 14kw serial number 6892965

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Generac Master
  • 25,459 Answers

It didnt start after cranking 3 times. its probably time for service and a valve lash adjustment, clean battery terminals etc etc

Posted on Apr 19, 2018


6 Suggested Answers

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 2006 Answers

SOURCE: my generac 15kw generator went

It could be either your start capacitor or the contactor-relay. Or you could try cleaning the contacts of the relay with an emery board to see if there is a change.

Posted on Sep 07, 2011

  • 2 Answers

SOURCE: how do i reset overcrank

You turn the unit to the off position, hit enter twice on control board, and put back in manual, this should reset this fault

Posted on Sep 08, 2011

  • 85108 Answers

SOURCE: GENERAC 14kw natural gas generator. Low RPM

I am sorry but you have selected the wrong product category. Please re-post in correct category. Thanks

Posted on Aug 29, 2012

  • 85108 Answers

SOURCE: Need a 2 wire start diagram for generac 14kw off grid application

Posted on Aug 30, 2016

  • 25459 Answers

SOURCE: Generator went into over speed today when it was starting for it's weekly test. What could have caused this and what is the solution? It is a 14KW Model 0058841 Generac Automatic Standby Generator.

you really need to list what generator you have. nobody here is going to guess at that one.

Posted on Nov 13, 2017

Testimonial: "Thanks, Steve!! Appreciate your help! I guess that information would help!! LOL!"

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Generac 14kw Propane generator won't start, just buzzes and displays cranking then RPM sensor loss.

if its not cranking clean your battery terminals and check the charge level. also check battery water levels

Jul 14, 2018 | Generac Electrical Supplies

1 Answer

Generac 14kw, overspeed fault

thers a problem with the stepper motor that controls engine speed according to generacs manuals. if you dont have one i suggest if you plan to repair it yourself get one . also join ziller electrics online forum for help

Nov 18, 2017 | Generac Electrical Supplies

1 Answer

Trying to find oil filter that can be found locally from car part supply store.

take the old filter along to the spares shop and see if they can match it up
I suspect that the same filter will fit both engines
if you want to get technical, use a verniers to measure the thread hole diameter, a thread gauge to get the thread pitch, and the outside diameter of the oil seal
by going to oil filters manufacturers on line and researching their catalogues you will find pages of filters with dimensions that will match you filter
I would rather just go and buy a genuine filter from a mower shop or kohler dealer as there may be a generic filter already listed.

May 05, 2015 | Generac Electrical Supplies

1 Answer

I need a wiring diagram for a generac 6551 model

Please provide the serial number of the unit and what diagram you are looking for as there are many. I will email you the diagram

Feb 25, 2015 | Generac Electrical Supplies

1 Answer

Generac troubleshooting my generac 14kw generator engine runs why doesn*t it produce electricity

Assuming the generator circuit breaker is on, depending on the model it could be the voltage regulator or the slip ring brushes or both. If it's a portable it could be a capacitor problem.

Jul 02, 2014 | Electrical Supplies

1 Answer

GENERAC 14kw natural gas generator. Low RPM alarm What should should I do to repair.

I am sorry but you have selected the wrong product category. Please re-post in correct category. Thanks

Aug 29, 2012 | Cars & Trucks

1 Answer

Generac generator remote start

si tiene transfer automatico solo poner un swicht en hilo 1N para cortar senal de entrada al generador del utility power que sensa la presencia de voltage en caso de falta arranca el generador en forma de prueba

Dec 19, 2009 | Generac 13,000 Watt / 13,000 Watt Home...

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

520 people viewed this question

Ask a Question

Usually answered in minutes!

Top Generac Electrical Supplies Experts

Sheldon Dedek

Level 3 Expert

909 Answers

Bob Janelli

Level 1 Expert

26 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Are you a Generac Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides