Question about Kenneth Cole Watches

Open Question

How can I locate an instruction Manuel for Kenneth Cole model kc1493?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Kenneth Cole KC3754

www.genevawatchgroup.com will come up on google, I got it to come up today, 20 Nov. '07 and clicking on the first heading that came up, "geneva Watch Groiup" I got on and was able to print out a repair service sheet for Kenneth Cole

Posted on Nov 21, 2007

Ad
  • 2 Answers

SOURCE: Kenneth Cole Reaction watch date set problem

I just dug my watch out after not wearing for a few years and had the same problem. There is an easy way to adust this watch's time and alarm, basically one way to enter both.

1) With the watch in the regular time display mode (doesn't matter if 12 hour or military time), depress and hold the lower left hand button (mode button). After a few seconds the watch appears to shift to alarm mode and it is blinking. This puts you into the mode for adjusting the alarm.

2) If you want to adjust time, date, etc rather than alarm time, after you have done step one, simply press that same lower left button again, and then it will put you into the time mode, but this time the time mode is blinking and you can adjust the various components (seconds, minutes, hours). You can only move minutes, hours, etc forward, no way to move backward. You will start off with the second display blinking, probably skip that unless you need to adjust seconds. Depress the upper right button to shift to the next option (minutes) and you will see the minute display blinking. Adjust the minutes by depressing the lower right button. When finished depress upper right button to move to next option (hours) depress the lower right button to move the minutes/hours/month/date forward as necessary, when you finish just press the lower left button again and it pulls you out of adjust mode and you are back in regular time viewing.

I had to post this because I've had this problem in the past and it killed me. Its kind of intuititve after you get into the adjusting mode by pressing the lower left button- remember, initially it will put you into adjust alarm mode, but press again and you will get into adjust time mode.

Posted on Nov 12, 2008

escapement
  • 2338 Answers

SOURCE: Kenneth Cole Wrist Watch unable to remove link

First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and start to unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet,make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!

Hope it'll help.

Regards

Arthur

Posted on Dec 17, 2008

  • 5 Answers

SOURCE: How to set kenneth cole unlisted digital watch with 4 buttons

OK I'll do my best to describe the procedure...

Part 1:
Press mode button till the seconds window blinks
Press Lap/Reset button once to make minutes blink
Cycle through minutes using Start/Stop Button

Part 2:
Press Lap/Reset button once again to make hours blink
Cycle through hours using Start/Stop Button

(for this part, it's a bit tricky. Hours can be displayed in AM, PM, or 24 hour duration. AM is represented by "A", PM is shown with "P" and 24 hour mode is shown with "H", so keep an eye in the seconds window when setting your hour so you know for sure if you have the right hour)

When your done setting minutes and hours, press mode button again till you get to main screen
A helpful hint is to remember when setting up anything in this watch, mode will cycle through the different screens, lap/reset will change the value of whatever your modifying (AKA minutes/hours) and start/stop scrolls through the different fields.

Hope this helps. Sorry if it's confusing, best I could do.

Posted on Dec 20, 2008

  • 2501 Answers

SOURCE: I need instructions on how to set day, date and

These wacthes are made by the Geneva Watch Group. Their web site is http://www.genevawatchgroup.com/

On the right of the screen is a menu, choose "our brands and then scroll down until you find the instructions for your watch.

Posted on Jun 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i set the kenneth cole duel time watch


Try Googling (Kenneth cole)(model)(manual) without parens for instructions.

Oct 08, 2017 | Kenneth Cole Watches

1 Answer

Manual kenneth cole for watch ul 1181 where can i get the manual


i am not understanding ......

you need Manuel for replacing battery ?

or

you need Manuel for setting up digital part of your watch ?

Jul 28, 2014 | Kenneth Cole Unlisted Chronograph Watch

1 Answer

I didint have the instruccion or manuel so i need to know how can i used properly its a UL 1159 s60


Kenneth Cole watches are made by the Geneva watch group.

If you go to http://www.genevawatchgroup.com/ and click on customer service, you can scroll down until you find the instructions for your model of watch.

Dec 13, 2010 | Kenneth Cole Watches

1 Answer

Keneth cole Rubber Strap Touch Screen Watch instruction manual


A technical support site is available online for the Kenneth Cole watch from where accessories user guides could be acquired. Locate Kenneth Cole online

Dec 02, 2010 | Watches

1 Answer

Where can i get a manual fot the kenneth Cole touch screen watch?


i have not been able to locate downloadable KC manuals. You can try at this link:
http://safemanuals.com/brand-user-guide-instructions-owner-manual/KENNETH%20COLE

Otherwise you can call 1-800-KEN-COLE to see if they can send you the info or email a downloadable version to you.
Good luck..

Aug 12, 2010 | Kenneth Cole Digital Chronograph KC1411...

2 Answers

How do I set the time on a kenneth cole kc1296 men's wrist watch


I couldn't find any instructions for your watch but my wife has a similar one and it goes something like this.

There are two recessed buttons which need to be operated by a thin probe.

One of them is a "mode" button which changes the operation from normal to setting mode.

When you have pressed the mode button you should see the "hours" flashing use the other button to change the time (there may be two buttons, one up and the other down), when you ahve the right hour press the mode button again and the minutes will flash. Adjust as for the hours and when all is OK, press the mode button again to return to normal operations.

Good luck, have patience!

Mar 14, 2010 | Kenneth Cole KC1296 Watch

Not finding what you are looking for?
Watches Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenneth Cole Watches Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Janelle Schoonover
Janelle Schoonover

Level 3 Expert

841 Answers

Gary Nitowski

Level 2 Expert

326 Answers

Are you a Kenneth Cole Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...