I just bought the d-link dir615 wireless N router 300mbps, 802.11n 4 port router. I have hooked it to my desktop and using my lap top wirelessly. My question is do I need an wireless adapter on my desktop to have my laptop read files/ printer on my desktop or can this be done through the d-link router. Thank you Hollis leon Elkins

Login to the router's web-interface, and use the "Setup Wizard" to configure the wireless network.

Here is a link to show how to set up the DIR635 without the CD:
http://www.instructables.com/id/D-Link-Wireless-Router-DIR-628-Setup-Without-CD/

hello
How do english upgurade DIR616 wireless router????

LAN PORTS ARE BAD SEEMS TO BE.

Hello
I can give some details on port forwarding for TL-WR940n. You could follow this procedure given below. here is the link too. http://www.tp-link.com/en/article/?id=72




How do I open ports on my TP-LINK wireless Router?


Suitable for: 300Mbps Wireless N Routers, 150Mbps Wireless N Routers, 54Mbps Wireless G Routers


Step 1 Open the web browser and type the IP address of the router (default is 192.168.1.1 or 192.168.0.1) into the address bar and then Press Enter.

Step 2 Type the username and password in the login page, the default username and password both are admin.

Step 3 Click Forwarding->Virtual Servers on the left side, and then click Add New... button.




Step 4 Type the Service port which you want to open and the IP Address of your computer; Select Protocol to TCP, UDP or ALL; Change Status to Enabled




Step 5 Click Save button to save the settings.

Note:
If you want to open port 80 for Web server in your computer, the Management port of the router will be changed to 8080, you need to type Http://192.168.1.1:8080 to connect to you router.




TP-Link_SupportForce
TP-Link USA Corporation
Tel: +1 866-225-8139
E-Mail: [email protected]
Website: www.tp-link.com/en/support/index.asp

I think there is no need to replace the ADSL2+ Router.
Belkin is fine and should work well in combination with the D-Link Router and you would get the downlink data rate up to 300Mbps.
I recommended that you use Belkin Router as ADSL Modem and Dlink to provide wireless access. (Instead of buying ADSL Modem)
So, all you have to do is : -
-Turn-off wireless signal of the Belkin modem.
-Connect the Dlink Router to the Modem (Belkin) through CAT6 Cable.
-Configure the Dlink Router, Secure it and Enjoy 300Mbps Data Rate.

(In this way your Belkin will serve as ADSL Modem and Dlink would be the wireless router)

Let me know if any further clarification/ assistance is required.
Hope it helps! Good Luck!
CreativeTECH

NO! It will work at the G router speed !

1. check your wireless adapter TCP/IP settings if its set into "Obtain as IP address Automatically".
2. if the settings is set as Automatic and your not getting IP address then select "Use the following IP Address"
3. use IP address followed to your router address like if192.168.0.1 in router type 192.168.0.2 or192.168.0.3 just check the next address IP in your network.
4. after typing subnet IP will automatically set
5. type the router IP address as your default gateway
6. click OK to save your new settings

Hope this will help

If you will connect your desktop to one of the ethernet ports, you will need an ethernet cable. and to customize the wireless settings you can visit this link to help you change the name of the wireless network. Setting-Up the Wireless Settings on a Linksys Router . And you can follow the steps here on this link on how to check or configure the wireless security settings.

Yes, I have pretty much the same setup at home. Wired desktop and wireless laptop. On the back of your wireless router, there should be 4 or 5 wired connections which you can use. You will only have to use the setup disk on one computer. Basically, the setup disk is for the router, not the computers, it simply guides you through the router configuration process. You can also do this manually, the manual for the router will give those instructions as well.