Question about Measuring Tools & Sensors

1 Answer

Temperature in/out 911711; changed batteries on bothe indoor and outdoor units. Outdoor temp not registering on indoor unit.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Measuring To... Master
  • 53,162 Answers

  • Remove all batteries
  • Install batteries in outdoor unit and allow it to initialize and begin sending data.
  • Install batteries in indoor unit. You should see outdoor temperature displayed
If not, either unit or both may be defective

Posted on Aug 07, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: model 6312026 Nexxtech 433MHz wireless

Hello, you have to push few second the mode button and after date, hour etc it will be possible to change F for Celsius. He will flashing and after push one of the two button up or down.

Bye from Quebec Canada

Posted on Nov 20, 2008

  • 81 Answers

SOURCE: U4 System transmission between indoor and outdoor units Daikin

Sounds like an interconnecting wiring error. Check wiring connection i.e. wires are connected in right order 1 to1 2 to 2 etc. from indoor terminal board to outdoor terminal board. Also check for slack or loose connections.
Hope this helps I take the time to answer your question so please rate me

Posted on Jun 28, 2010

  • 3289 Answers

SOURCE: The outdoor temperature & hygrometer

Hi Walter,

I found this in the manual, simply pressing the RESET button won't start communication again. Try this:

Your main unit displays current, minimum, and
maximum temperature and humidity readings
collected by the remote sensor and main unit.
Outdoor data is collected and displayed every
40 seconds and indoor data is collected and
displayed every 10 seconds.

The red LED flashes whenever the sensor
transmits an RF signal to the receiver.
select sensor or use auto scan

• Press CHANNEL to switch between
sensors 1-3.
• To auto-scan between sensors, press and hold
CHANNEL for 2 seconds. Each sensor's data
will be displayed for 3 seconds. To end autoscan,
press CHANNEL or MEMORY.
• Press and hold CHANNEL and MEMORY
simultaneously to search for remote sensors.
resetting the system
The RESET buttons are located on the back of the
main unit and sensor. Use a pointed subject to
press RESET when you change the batteries and
whenever the system malfunctions.

Posted on Jul 13, 2011

  • 1 Answer

SOURCE: I have the Acurite 00604RX

how do i set my clock for accurite 00604RX

Posted on Sep 07, 2011

vasanks
  • 1 Answer

SOURCE: i put new batteries into both units, the indoor

Sometimes the RF frequency from the outside transmitter loses contact with the clock's frequency ( it has happened to me only twice in 6 years ), and then the outside temp will not show. Simple solution to fix this is: Take down the outside transmitter and the internally mounted clock. Remove batteries from both. Wait about 10 mts. First install batteries in the transmitter, then after about 30 seconds, install batteries in the clock. In about 5 mts, you will find the clock showing the external temp like before.

Posted on Feb 26, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The weather channel how do I reset the outdoor temp?


  • Remove all batteries from both units
  • Install known-good batteries in outdoor unit. Allow time for outdoor unit to initialize and begin sending data
  • Install batteries in indoor unit. You should see outdoor temperature displayed

Jun 04, 2018 | Weather Channel Measuring Tools & Sensors

1 Answer

Changed batteries and now cannot get an outdoor reading.how do I fix this?


  • Remove all batteries
  • Install batteries in outdoor unit
  • Make your way indoors at a leisurely pace. This allows the outdoor unit to initialize and begin sending data
  • Install batteries in indoor unit. You should see outdoor temperature displayed
In cold weather, the outdoor temperature display may disappear due to frozen batteries. At the moment my reading is - - because it is around 40 deg. F. However, in a day or two when the outdoor temperature reaches 50 deg., the outdoor temperature will be displayed again. All in all, rather whimsical.

Jan 22, 2017 | Measuring Tools & Sensors

1 Answer

Just put new batteries in both units but can't get the oudoor temp to show - what have ee done wrong?


Replacement has to be done in a certain order.
  • Remove all batteries
  • Install batteries in outdoor unit. Allow time for unit to initialize and begin transmitting temp.
  • Install batteries in indoor unit. You should see outdoor temperature displayed.

You may find that the outdoor temperature is not transmitted in very cold weather. Right now it is below freezing and my indoor unit is showing - - for outdoor temperature.

Dec 13, 2016 | Measuring Tools & Sensors

1 Answer

Model WS9611UN-IT - I am unable to receive the outdoor temperature. I have changed the batteries on the outside remote but I still do not receive the outdoor temperature. How can this be corrected


Remove all batteries, both outdoor and indoor. Install batteries in outdoor unit and wait for it to begin sending a temperature signal. Install batteries in indoor unit. You should see outdoor temperature displayed. If not, batteries, transmitter, or indoor unit may be defective.

Nov 16, 2016 | Measuring Tools & Sensors

1 Answer

Out do I get the outside temp back.


You have to remove all batteries, both outdoor and indoor. Install replacement batteries in the outdoor unit. Back indoors, install replacement batteries in the indoor unit and wait for temperature to be displayed. If nothing happens, the outdoor unit may have failed.

Jun 17, 2016 | Measuring Tools & Sensors

1 Answer

Why isn't outdoor temperature displayed on indoor unit?


I have a La Crosse unit right in front of me and it is showing +18 F tonight. Saturday, we are supposedly going to sub-zero.
With regard to your problem, La Crosse instructions are very specific about the battery replacement procedure. Remove all batteries from both units, then install new batteries in the outdoor unit. Allow time for the outdoor unit to "initialize" and begin sending temperature data. Install new batteries in the indoor unit and you should see the outdoor temperature displayed.

Feb 12, 2016 | La Crosse Technology Wireless Temperature...

1 Answer

Why isn't outdoor temperature displayed?


Try repeating the initial set up procedure. Remove all batteries from outdoor and indoor units. Install known-good batteries in the outdoor unit. Allow time for the outdoor unit to begin transmitting data. Install known-good batteries in the indoor unit. You should see the outdoor temperature displayed.

Feb 09, 2016 | AcuRite Acu-Rite 00621 Wireless Weather...

1 Answer

How do I get the -- away and get the outdoor temperature to work?


You may have to "reset" it by removing both indoor and outdoor unit batteries, waiting briefly, then reinstalling batteries in the outdoor unit followed by the indoor unit. After awhile, the outdoor unit should begin sending information to the indoor unit.

Nov 20, 2014 | Oregon Scientific Wireless Weather Station...

1 Answer

Radio Shack 63-1090 indoor/outdoor temperature unit. Won't give outdoor readings. Temps are cold, -5F but it always worked before. Put in new batteries in the inside and outside units, wiped outdoor sensor...


According to instructions for similar systems, you have to replace batteries in the outdoor unit first, then the indoor unit and wait 10 minutes without pressing any buttons for the indoor unit to begin displaying the outdoor temperature.

Dec 31, 2013 | Heating & Cooling

1 Answer

ONLY SHOWS INDOOR TEMPERATURE DOES NOT SHOW OUTDOOR TEMPERATURE


I have a similar device and the instructions say to remove batteries from both units and wait for 10 minutes without pressing any buttons before installing batteries first in the remote unit then the indoor unit. The outdoor and indoor units have to "talk" to each other before getting in the mood to display temperatures.

Feb 03, 2013 | Oregon Scientific Wireless IndoorOutdoor...

Not finding what you are looking for?
Measuring Tools & Sensors Logo

Related Topics:

629 people viewed this question

Ask a Question

Usually answered in minutes!

Top Measuring Tools & Sensors Experts

Vuk B

Level 3 Expert

717 Answers

Brad Brown

Level 3 Expert

18072 Answers

Tom Chichester

Level 3 Expert

53135 Answers

Are you a Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...