Question about Lanier Office Equipment & Supplies

Open Question

Lanier LD035: Smug on drum.I took drum unit out cleaned drum . Put it back in got error code 819 6261 0x64206469.

Lanier LD035: Copies were displaying a lot of dust. I replaced toner, drum , and developer. Hit copy sample. It work fine except smug on drum. I took drum unit out cleaned drum . Put it back in got error code 819 6261 0x64206469. Will I need to replace hard drive or simply replace drum to clear error? No technician available for my area.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Soulvisitor
  • 1113 Answers

SOURCE: Dust on Drum message after installinng new Drum

Dust on drum refers to as you correctly stated the wire, it carries a electric charge that transfers the image. If the wire gets contaminated the electricity dont flow right so dust on drum is desplayed, you drum cart is faulty, they are not repairable items, go buy another then claim new/old one as faulty from them. Um aH.

Posted on Dec 19, 2007

Ad
  • 53 Answers

SOURCE: xerox 5305 copier excess toner

sounds like faulty drum cleaning blade,which is usually contained in the replacement drum module.I would be inclined to take the drum unit back where you got it (unless you replaced it with a second-hand one) 99% certain the problem is contained in that module

Posted on Feb 27, 2008

  • 1 Answer

SOURCE: Aculaser C2600 "clean sensor" message

This is a common characteristic which arises from using improperly remanufactured toner cartridges.
Otherwise it is a bad Epson original one - which is highly unusual!

When the C2600 runs through its calibration it prints strips of each colour on the transfer belt which are sensed for density. You will get a "clean sensor message" if the reading for any of the strips drops below a certain value.

The first thing to do is to depress the clean sensor lever behind the front cover several times . If that doesn't fix it I would advise you to remove each cartridge in turn (go to reset menu and scroll down to change toner) and inspect the toner on the surface of the roller. If there is any form of "sheen" then you'll need to replace the cartridge.

It is possible to adjust the doctor blade if you know what you're doing but be careful as there are shims on each side. Loosening and moving the blade bar towards the roller slightly, refixing and then turning the side cog to rotate the roller can sometimes resolve problem. Not a good idea really unless you're in an emergency.
There are some good remanufactured cartridges and bad ones. If you want to avoid this buy genuine Epson cartridges - I know they're expensive but what does the down time cost!

Posted on Jun 19, 2009

  • 2 Answers

SOURCE: Dust on Drum...

I had this problem too. I took out the drum and vacuum the drum with a vacuum cleaner ( no brush ) while at the same time manually rotate the drum cyclinder. It worked. After a month or two, you might have to do it again. But everytime, it solved the dust problem.

Posted on Nov 28, 2009

  • 158 Answers

SOURCE: Konica/Minolta biz 350 C2557 after replacing DV unit and drum F8

tha minolta di3510 developer unit looks the same as the unit for the konica minolta bizhub 350 but the toner sensor in the minolta unit uses a different voltage range for the toner sensor and it will throw this code make sure you have the correct unit for this machine also you can try this
go back into tech rep mode and change these settings:
select tech rep choice mode
select printer tab
select atdc sensor gain
set the value to about 165
then back all the way out to the ready screen and power the machine off then back on and replenish toner in the user management screen.

Posted on Nov 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lanier error code 00


That is the master clamper area. Take off the rear cover. From the rear it is on the right. There is a motor and a rack gear that moves to open the drum master clamper when removing and loading a master. With the back cover removed, try to make a master while watching that assembly. You can also put the drum in and drive the motor by hand to watch and see if opens the drum clamper.

Dec 12, 2014 | Lanier Office Equipment & Supplies

1 Answer

How do you set the Lanier LD035 duplex unit?


Metal tab on right side of copier is bent and correctly touching the duplex unit interlock switch. Open the duplexer and notice the metal tab stick out. Put back to a 90 degree angle.

Jul 30, 2014 | Lanier Office Equipment & Supplies

1 Answer

Lanier 5635 Sorter


Under user tools, system settings make all prints, copies to come out in internal tray, the front and rear covers have to come off to remove screw 1 each side the SC code is shift tray motor error

Dec 18, 2013 | Lanier Office Equipment & Supplies

1 Answer

I have a black line on my copies. i have a lanier 7320 copier. Is it my drum?


It could likely be the drum. Is the line on copies and prints, or just copies? If it's just on copies, it's not the drum.

Jan 18, 2011 | Lanier 1205 Copier

1 Answer

Lanier 5635 error code displaying a SC320


sc320 on the Lanier 5635 is a laser unit error code. Often if you power cycle the machine (turn it off with the orange power switch on the left side of the copier, wait a few seconds, then turn it back on) the code will clear and the copier will resume normal operation. If the error code comes back or doesn't clear, you'll probably need to replace either the entire laser assembly or the polygon mirror motor inside the laser unit. These are best done by a professional -- contact your local Lanier service company if the problem persists.

Oct 15, 2010 | Lanier 5222/27 Laser Printer

1 Answer

My lanier is making dark copies


One of the most common reasons for a Lanier 5222 or 5227 to make dark copies is a problem with the drum unit or developer. Fortunately on those machines, the drum unit and developer are all self-contained in one easily-replacable unit, called the PCU (photoconductor).

If you don't have a new PCU handy, you can order one from the same company you get your toner from. The PCU should generally be replaced every 60,000 copies, but sometimes it may need to be replaced sooner (especially if you run a lot of dark copies or make a lot of copies of images) and it can often run longer than 60,000.

Replacing the PCU is easy -- it sits right next to the toner bottle, and all you have to do is slide the old PCU out and slide the new PCU in (once you remove all of the tape and other trappings from it). Instructions will be included in the box with the new PCU.

Please rate the effectiveness of this solution. Thank you!

Oct 10, 2010 | Lanier 5222/27 Laser Printer

1 Answer

I have a ricoh mpc 3500, it works fine but i am getting black lines on my copies.


Hello sir; There are two way to get rip off the lines,# 1 , aat the end of the transfer belt there have a cleaning unit , clean up , if need to replace cleaning blade , change it. #2 , after you copy , pull out each drum unit check it out see which drum with the line on it, replace that drum unit.

Aug 15, 2009 | Lanier Office Equipment & Supplies

2 Answers

Dark copies with overprinting


Cleaned the coronas as per instruction book. Done this before but this time it made a difference.

May 07, 2009 | Lanier 1205 Copier

2 Answers

Lanier 5622 Prints vertical lines


You could remove the color and black&white drum units and check from below the units to visually observe lines on all the 4 drums. If so, you have to change the drum unit/units. Drums occassionally get damaged before life this way due to solid toner particles inside the toner bottle.Always "shake the toners very well" before replacement, and if you print rarely, then remove the toners and do the shaking to prevent clogging due to inactivity.

Aug 28, 2008 | Ricoh CL4000DN Laser Printer

2 Answers

Printing problem with lanier 6720 printer


Check your photo conductor (drum) unit. This is often caused by an old or light damaged unit.

Sep 15, 2007 | Lanier 5235 Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lanier Office Equipment & Supplies Experts

quennie732

Level 2 Expert

422 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

gggg

Level 3 Expert

904 Answers

Are you a Lanier Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...