Sub will drain all the sound off the front speakers

Question 1

0helpful

1answer

I have 2 mtx thunder 6000 12inch subs. one works great but the second one act's like a speaker wire is crossed but all the wires are right. i can hook both subs to the same channel and the first one...

May have a blown channel in your amp.

May 19, 2011 • Car Audio & Video

0helpful

1answer

How big of hole do i need for the mtx 6000 thunder 10in

The MTX Thunder 6000 T61544A is a 15" Subwoofer meaning you will need a 15" hole to fit the subwoofer into. The mounting plate that surrounds the subwoofer will extend past 15" allowing you to screw the sub in properly. Be sure to use a box that is at least 12 inches deep (sub is 10 inches deep by specifications + 2 inches for good air cushion behind.

Mar 01, 2011 • MTX Thunder 6000 T61544A Car Subwoofer

0helpful

1answer

I haw alpine mrp-m350 amplifier how many sub can i

Hook up the MRP-M350 to one 4-ohm sub, and you get 200 watts RMS; connect a second 4-ohm subwoofer and the power output increases to 350 watts! All that juice means that your subs won't just be loud, they'll sound clean and thumping.

Apr 08, 2010 • Alpine MRP-M350 Car Audio Amplifier

2helpful

2answers

MTX 12'' sub noise

Sounds like your sub is overextending itself, and possibly losing contact at the voice coil. Overextending will make a weird rattling sound, losing contact at the voice coil will make a popping sound.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Jan 12, 2010 • Car Audio & Video

0helpful

1answer

I have 4/3/2 ch. alpine f-240 amp- i want to hook up four 6x8 3-way and one 12''sub. the amp has bass EQ on ch. 3. how would i hook it up and get the most power. can i put the 4 6x8 bridged all together...

run two 6x8s on each of the front channels of the amp. then depending on the sub you can bridge it on the rear channels.only if its a single four ohm. if its a dual 2 ohm sub run each coil on each channel. 1 coil-1channel. the other coil-the other channel. amp should run fine may run a little hot since it will be doing all it can do at a safe ohm load. just make sure it is mounted in a well vented area. should be safe.

Dec 25, 2009 • Alpine MRP-F240 Car Audio Amplifier

0helpful

1answer

Sub not working and red light on amp stays on?

the amp is under to much pressure get a bigger 1

Nov 18, 2009 • MTX Thunder 421D Car Audio Amplifier

1helpful

1answer

Can this power a subwoofer and what is the rms wattage

Hello crucible19,

The Alpine MRP-F240 is a 4-channel amp that outputs 40 watts RMS per channel. It is more suited for powering normal speakers, but since it is bridgeable, you could power a small sub by bridging 2 of the channels.

Hope this helps.

Oct 02, 2009 • Alpine MRP-F240 Car Audio Amplifier

1helpful

1answer

I have one mtx t4510-04..what amp do you

Hello jandytaala,

The recommended power range for you T4510-04 is 112.5 to 225 watts RMS. So you need a monoblock amp within that range. You could go up to about 300 watts RMS, but watch the gain and don't try to get too much from a single 10" sub.

The Orion Cobalt shown here would be a good match and is only $139.99. For another $60, the Alpine MRP-M500 will output 300 watts into 4 ohms.

Hope this helps.

Aug 28, 2009 • MTX Thunder 4500 T4510-04 Car Subwoofer

0helpful

2answers

What is the best way to connect 4 speakers and a sub to a 4 channel amp.

I would connect the 4 speakers to channels 1-2 in stereo with high pass filter. Bridge the sub to channels 3-4.
A thumbs up would be greatly appreciated if this answer is helpful to you. best-way-connect-4-speakers-sub-4-zb4bomd1rt4qms0dqd12kkt2-3-0.jpg

best-way-connect-4-speakers-sub-4-zb4bomd1rt4qms0dqd12kkt2-3-0.jpg

May 01, 2009 • Car Audio & Video

0helpful

1answer

Has my subwoofer been blown?

hook ithe sub up to a 9volt battery and see if the woofer moves... You will not dammage the suub testing it this way.

Mar 23, 2009 • Alpine Type-R SWR-1242D Car Subwoofer

Question 2

Anonymous

Expert 50 Answers
Posted on Jul 25, 2009

Anonymous

Expert

Joined: Jun 04, 2009

Answers

50

Questions

3

Helped

14203

Points

114

If you have both amps connected to the same power wire this will happen...run another power wire to the alpine and this should solve the problem.

Related Topics:

Trustworthy Expert Solutions

Sub will drain all the sound off the front speakers

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

I have 2 mtx thunder 6000 12inch subs. one works great but the second one act's like a speaker wire is crossed but all the wires are right. i can hook both subs to the same channel and the first one...

How big of hole do i need for the mtx 6000 thunder 10in