Question about Lanier Office Equipment & Supplies

Open Question

Lanier c3002 - I need to reset the SC code sc552-02.

I cleaned the thermistors in the fuser which were dirty. I tried using the instruction for Ricoh, but using either clear or reset, then 107 and holding stop did not work to get me into the next screen. SOLVED: Use Reset - 107 - Clear. NOW YOU ARE ON YOUR OWN. I believe following the rest of Ricoh instructions might work, but we had a service tech lead us through.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Soulvisitor
  • 1113 Answers

SOURCE: Minolta Error code C0500

1. Test Mode Operations
• The Test Mode is performed from the copier’s Tech. Rep. Mode.
1-1. Entering the Tech. Rep. Mode
1. Press the Utility key.
2. Touch [Total Check].
3. Press the following keys in order: Stop → 0 → 0
→ Stop → 0 → 1.
NOTE
Be sure to keep the display procedure for the Tech.
Rep. Mode from any unauthorized persons not
involved with service operations.
4344S504CA

link to a service manual that explains tech mode

Posted on Dec 02, 2007

Ad
Bubbabear64
  • 2794 Answers

SOURCE: How to clear error code SC571 on Ricoh 1232c copier

See thread I left you this morning on this. I hope it helps.

Press the yellow button. Press the 107 keys. Press and hold the red clear button for a few seconds until the service mode screen appears on the LCD display.

Posted on Nov 06, 2008

Joed911
  • 4338 Answers

SOURCE: Lanier LD060 has a SC541 Error Code

Troubleshooting tips:
Enter SP Mode by holding down "up" and "down" arrow for 10 s then you press "enter"

SC 541 Heating roller
thermistor error
The temperature measured by
the heating roller thermistor
does not reach 7 °C for ten
seconds.
• Loose connection of
the heating roller
thermistor
• Defective heating roller
thermistor
• Defective BCU
1. Check if the heating roller thermistor
is firmly connected.
2. Replace the fusing unit.
3. Replace the BCU.
Controller
errors CTL The error has occurred in the
controller.
See .Troubleshooting Procedure. in
the table.
A
The error involves the fusing unit.
The machine operation is disabled.
The user cannot reset the error.
Turn the main switch off and on.
Reset the SC (set SP5-810-1). Enter the SP Mode by holding down "up" and "down" arrow for 10 s then you press "enter"
Turn the main switch off and on. Also, check info on this link: http://helpdeskgeek.com/how-to/ricoh-aficio-cl7200-printer-sc541-error/ If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Posted on Mar 11, 2009

  • 15 Answers

SOURCE: How do I get to Tech Rep Service Mode on Minoltas to clear C0500 error code?

I need to know m/c model

Posted on Apr 09, 2009

Ickoajnc
  • 211 Answers

SOURCE: service mode

Press the “Up/Down arrow” keys together for about 5 seconds, and then press the
“OK” key.

“SYSTEMver x.xx/ 1. Service” appears on the display.

The machine automatically goes off line when you enter the service mode.
enter SP 5810 and reset the SC 543 **** if again appears please do not reset it again because you may do bigger problem and damage more part than ware damaged in first place .
The SC code says that the termistor is damaged so check on the fusing unit dose the termistor is standing in good position or has dirt on the surface of he termistor.
RATE ME IF THIS HELP YOU

Posted on Jul 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What is error code SC542 for ricoh aficio 9005?


Ricoh Aficio MP2510, 3010 Error code sc542 on Lanier ...

? 6:08
https://www.youtube.com/watch?v=58MQVyjfDyg
Sep 3, 2013 - Uploaded by Used .Copier
Are you getting Error Code sc542 on your Ricoh, Lanier,Savin or Gestetner copiers? ... Ricoh Aficio 1022 ...

How to reset Ricoh Error Code sc542 sc546 sc548 problem ...

? 2:41
https://www.youtube.com/watch?v=3CnGl1Ytp34
Sep 21, 2015 - Uploaded by Copier Liquidation Center
How to reset Ricoh Error Code sc542 sc546 sc548 problem ...Ricoh Aficio copiers : AFICIO 1013 F

Dec 02, 2015 | Ricoh Aficio Office Equipment & Supplies

1 Answer

Ricoh Aficio SP 4210N- Code SC 543


This is a common error code for Ricoh copiers, Savin and Gestetner copiers that need service. Recently Ricoh has purchased Lanier and now is naming all their new machines Lanier instead of Gestetner, Savin and Ricoh. However, the copier service error codes have remained he same.
When you get this copier printer service code it means the fuser or fixing assembly (same part) has thermistor problem. The copier fuser's thermistors help regulate the temperature of the fuser assembly. The fuser assembly on all copiers including Canon, Kyocera, Ricoh, Sharp and other brands is the part that melts the toner onto the page.
Getting back to the repairing the copier on Ricoh, Savin, Lanier and Gestetner models that have the fuser or fixing code error. The majority of the time the fusers' thermistors (Middle and read) need to be replaced. Just cleaning them will not solve the copier repair service code.
It is usually, depending upon the machine, its a 1 to 2 hour copier repair job because the copier repair service technician will need to dissemble the fuser, insert the two new thermistors, re-assemble, reset the error code and test the copier machine repair. Also, ask the copier technicians to to do a copier cleaning maintenance while on site.

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Aug 18, 2011 | Ricoh SP 4210N Laser Printer

1 Answer

Please have you solution for the Error codes SC545 for Ricoh Aficio 3035 macine


fuser over/under heat u need a service engineer to reset it
reasons
1 thermistors dirty
2 thermastat blown
2 lamps blown
try resetting it 1 st
press yellow key then 107 then hold red key for longer than 5 sec
go to section 5 (mode i think) then 810 sc reset press 1 then hash key off on

Oct 31, 2010 | Ricoh Aficio 450 Copier

1 Answer

Showing error message sc541


this is an error for the fuser the thermistors have not registered the temps properly check the fuser and if you know how to take it apart clean the thermistors.. you could try an sc reset using the following proceedure...Yellow clear button then 107 then hold down the stop button..wait for the screen to change to show copier sp turn off the machine and wait 5 secs then turn off. If this doesnt reset do the same proceedure on the copier sp enter this then look for mode 5. enter this mode and look for 810 sc reset and set this then turn off wait and turn back on....if this error occurs regularly the thermistors will have to be changed.. hope this helps..A

Jun 28, 2010 | Lanier Office Equipment & Supplies

2 Answers

I need the fuser reset code for the Ricoh Aficio 350


Hello,

Try to reset with 5801 it means:

enter service mode with 107 and find 5801 and execute then switch on and off the copier.
Please try if it works.

Oct 15, 2009 | Ricoh Aficio 350e Printer

3 Answers

I have a ricoh aficio 2035 that reads error sc 546 problem


It is fuser code, to reset enter the sevice mode by pressing All clear 1,0,7 & Keeping Stop button pressing, Press the copy Mode, then OFF & ON the m/c, the code will cleared.

Aug 17, 2009 | Ricoh Aficio 450 Copier

5 Answers

Ricoh aficio 1022 sc 546


problema ricoh aficio 1022 copia en blanco aparece codigo
sc 193

Oct 20, 2008 | Ricoh Aficio 1022 All-In-One Laser Printer

2 Answers

Error code 541


hi!!!!

may be the drum is damaged
try to clean it use dry tissue
or
repkaced the drum!!!

Sep 16, 2008 | Ricoh Aficio 2018D All-In-One Laser...

2 Answers

SC 541


Take the fuser out and clean under the thermistors, and reset the code by entering test mode ( turn off printer hold down online and escape as you turn on printer selece 2 engine go to sp5-810 and reset this.
-Carl, please let me know if this helps.

Jul 30, 2008 | Ricoh Aficio AP600N Laser Printer

5 Answers

Ricoh 3006


go to service program 5-810 ( sc reset) press on, turn off the machine an the turn on again. The service code should be gone, if it come back again check for a paper jammeed or wrapping the upper
fusing roller if this is not the case replace the thermistor;
Good luck
Vittorio

Dec 21, 2007 | Ricoh Aficio Colour 3006 Color Copier

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lanier Office Equipment & Supplies Experts

quennie732

Level 2 Expert

422 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

gggg

Level 3 Expert

904 Answers

Are you a Lanier Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...