Same here Code 46. Had to replace the mother board last year which seemed to fix a similar problem (but code 61 at that time) - condensor tries to start but kicks off several times then code 46 displayed. Need another new circuit board or is it really a thermistor problem?

E6 46 is a diagnostic code for a Whirlpool gas range. This code indicates that there is a problem with the oven temperature sensor. The sensor measures the temperature inside the oven and sends this information to the control board. If the control board detects a problem with the sensor, it will display the E6 46 error code.
To troubleshoot the problem, you'll want to do the following:

1. Check the wiring: Make sure that all of the wires connected to the oven temperature sensor are secure and not damaged.
2. Check the sensor: The oven temperature sensor is located in the back of the oven, near the top. Make sure that the sensor is properly seated in its socket and that it is not damaged.
3. Check the control board: If the wiring and sensor appear to be in good condition, the control board may be the cause of the problem. You'll want to check the control board for any visible damage or loose connections.

If you are unable to find the problem, I recommend having a qualified repair technician diagnose and fix the issue for you. Electrical issues can be complex and it's important to address them promptly to prevent further damage.

google finds it so google it first.
or ask the maker.???


https://www.boots.com/boots-pharmaceuticals-blood-pressure-monitor-upper-arm-unit-10217395

I had similar problems with my GE and had to replace the control board. Solved the problem but when I examined the failed board the main filter capacitor was bad whic I replaced. I do not know if it fixed it I never put it back in.

There's a fuse on the power supply board if not blown change the power board I found one for 8 dollars on eBay.

If you have not used the camera in a long time try to reset it. If it was installed on your computer try to reinstall it. Sometimes that will work . I hope this helped a little.

Yes,tries websites like Tvrepairworld.com,Partstore.com,Ebay.com to buy a projection lamp for the replacement.Tv have "LAMP"indication LED light is flashing or staying on.If the projection lamp on the tv now,been in used 4 or 5 hours a day watching the tv.The projection lamp has not been replace the last 1 1/2 or 2 years on the tv.The projection lamp life is over,require changing.The tv also making clicking noises,the Ballast board also dead,require changing too.The Ballast board help to ignite the projection lamp.

All DLP TVS are lemons really.Most the Convergence ICS,they use on the board held the picture together will alway die about 1 year or 1 1/2 year all way need it replace.The bulb have life spans but never reaches alway dies before than.

• For starview super box
• Press MENU
• Press 1570
• Go to NAGRAVISION and press OK
• Go to Key Number with the arrows on your remote, press two times to the right. Now you should have 00 again
• Go Key Data and enter this code: B0 B8 4F 04 E6 5F 87 80 and press OK.
• Go back to Key Number and press arrow to change to 01
• Than go back to Key Data and enter code: A3 EB EC 07 06 49 D2 EB and press OK.
• Last step: press EXIT 3 times. Your channels should be now restored.
• Ps. Make sure to install all numbers and letters of the code don’t over look any of them for this will cause problems reinstalling your channels…. try wit eurovox

download BIGMAQ toolbar and it has all the latest codes on the toolbar.

*for irish users do not use the NTL tab code go into the IRELAND tab and select either ireland NTL or ireland CHORUS*

same description , the same problem:I
had a power surge and now my G.E. dryer is showing Error Code 61. How do I reset it? I have turned the breaker off and on but this doesn't fix it.
I am JD and my e-mail is : [email protected]
Thank you all¡