Panasonic EL52253 cordless phone: after completing a call, the in use light on the base remains lit unless the user presses the red OFF button on the phone. Can this shutoff be made automatic?

My phone is from the same Panasonic line.

Since you can call out it seems to me that it is the phone company's error message..

"All circuits are busy" and "this number is no longer in service" are telephone company error messages.

Did you have this problem with other phones? Maybe you can take the phone to a friend's for family's home and try it there. If the phone is okay, call Telus back and let them know that the phone tested okay and ask what they are going to do to fix the problem.

Seems to me that their circuits are overloaded and they are blaming your phone because it is something they can't repair. Only fixed by them spending $$ to increase/ expand band width.

Yellow light constantly blinks on top of all the cordless phones

www.faqqq.com/.../yellow-light-constantly-blinks-on-top-of-all-the-cord...

Question Product: Panasonic KX-TG5432 Digital Dual Cordless Telephone Question Details: Yellow light constantly blinks on top of all the cordless phones The.

Panasonic KX-TGP550 Normal Status Lights

www.statuslights.com/panasonic/panasonic-kx-tgp550.html

Red (Rapidly Flashing), The Base Unit is paging handsets. (KX-TGP-500 only). Amber(Solid), The Base Unit's IP address may conflict with the IP addresses of ..

Go to Settings > SOUND > Silent mode (No sounds except media and alarms).
If this is ticked (on), it means umts smartphone alarm will sound even if you make the phone silent.
Regarding the loud sound even after reducing ringer volume, no idea for this.

I couldn't find the exact manual for your phone but I would try to re-register the phone. Following are some instructions for similar models of your phone.

*To do this on a non-expandable cordless phone:

• Press and hold the LOCATOR/INTERCOM button on the Base until a beep sounds.
• Press and hold the FLASH/CALL WAIT button on the Handset until a beep is heard.
• When registration is complete, a beep sounds from the handset.
• Wait for 20 seconds after registration is complete to allow the handset to establish communications with the base.

If this fails to help: Remove the AC Adapter from the phone base or wall outlet for a few seconds and reconnect. It may also be necessary to remove the battery from the handset for a brief moment.

Good luck!

1 Enter Pairing mode.
• Turn off your headset and press and hold the Multifunction
button until the blue indicator light remains lit
after blinking.
• If you turn it on for the first time, it proceeds into Pairing
mode immediately.
2 Search for and pair with your phone according to your
phone’s user guide. (Bluetooth PIN: 0000, 4 zeros)
• If the pairing is successful, the blue indicator light will
flash 10 times rapidly before entering Standby mode.
• If the blue indicator light remains lit, retry pairing.
Pairing with your Bluetooth phone
When the headset and the phone are paired, the
headset attempts to reconnect automatically each
time it turns on. Otherwise, press the Multi-function
button to reconnect.

USER GUIDE

This may help. It's from the Panasonic help page:

You may try to:

Disconnect AC power adapter from the back/bottom of base unit, then connect it again properly.
OR, to resolve this issue, you have to re-register the handset.

• To do this on a non-expandable cordless phone:
  Press and hold the LOCATOR/INTERCOM button on the Base until a beep sounds.
  Press and hold the FLASH/CALL WAIT button on the Handset until a beep is heard.
  When registration is complete, a beep sounds from the handset.
  Wait for 20 seconds after registration is complete to allow the handset to establish communications with the base.
  If this fails to help:
  Remove the AC Adapter from the phone base or wall outlet for a few seconds and reconnect. It may also be necessary to remove the battery from the handset for a brief moment.
  
  
• To do this on a expandable cordless phone system:
  Press and hold the LOCATOR/INTERCOM button for the extension that is displaying "No Link To Base" on the Base until a beep sounds.
  Press and hold the FLASH/CALL WAIT button on the Handset that is displaying "No Link To Base" until a beep is heard.
  When registration is complete, a beep sounds from the handset.
  Wait for 20 seconds after registration is complete to allow the handset to establish communications with the base.
  If this fails to help:
  Remove the AC Adapter from the base or wall outlet for a few seconds and reconnect. It may also be necessary to remove the battery from the handset for a brief moment.

I had this happen. After searching around here and elsewhere, I decided to look at the base station for the phone instead of the phone itself. In the lower right corner of the base station is a button labeled "Do Not Disturb" in inset print. The red LED above it was lit. I pressed the button and this cleared the problem.

For KXTG1000 only

The base unit must be connected to the AC adapter and the power must be on

Press the following sequence of buttons on the base unit: * * 3 3 5 7 8 2

When the display reads "Enter Base ID", deregistration has been completed successfully

For KXTG1050 only

Disconnect the AC adapter

Hold the Locator button down while you plug in the AC adapter

When the Power light flashes, release the Locator button

Immediately press and hold the Locator button again, and release when the In Use light flashes

The Charge light should flash for 4 to 6 seconds and then turn off

When the Charge light stops flashing, press Locator again

In about 20 seconds, the handsets will deregister. When the displays read "Enter Base ID", deregistration has been completed successfully.

A good trick to ensure a good connection for a cordless phone to it's base is to clean the silver connection points with a pencil eraser.