Connex mic has a red,blue,black,white,and a clear wire with a bare wire wrapped arround it what pins do they go to

I have other people that wire my mikes for me but if you go to cbtricks.com and look it up you might just find it.

I too have an Oricom 6 pin mic with wires broken pin 1 is white, 2 is black and 5 is screen, this does not match any of the above answers and the green blue & red are off with 2, 3, 4, & 6 available

Kevin H

• With the switch sitting as it is in the picture below (actual switch recessed tho the right. Soldier the wires in this order.

1. Black
2. Red
3. Lite Blue.
4. Dark Yellow (This yellow wire comes from the mic cord itself)
5. Shield.
6. Lite Yellow. (This yellow wire runs off to the side of the mike to the electrical components inside the mic)

• Standard 4 pin Cobra mic tip to run it to that Connex.

• Pin 1 - Shield.
• Pin 2 - White.
• Pin 3 - Red.
• Pin 4 - Black.

• If you have any comments please feel free to leave them here.
• Hope this helps and thank you for using FixYa.

Regards, Tony

Here are the Pin outs for different mics that will work with your radio. If a wire is not listed then you cut it off. It's best to keep the wires as short as possible no longer than a half inch is suggested. Normally the Cobra pin out is standard for most radios.

Stock - 1- Shield (Ground) 2- Yellow (Audio) 3- Red (Transmit) 4- White (Receive)

Astatic - (4 wire) 1- Shield 2- White 3- Red 4- Black

Astatic - (6 wire) 1- Shield & Blue 2- White 3- Red 4- Black Yellow NC

Daiwa EM-500, Cobra, CA Series - 1- Shield & Black 2- Red 3- White 4- Blue

Galaxy DC-521S - (4 wire) 1- Shield 2- Yellow 3- Red 4- Black

Galaxy CB-660EI - 1- Shield & Black 2- White 3- Red 4- Blue

Sadelta - 1- Shield 2- White 3- Brown 4- Green

Turner - 1- Shield & Red 2- White 3- Blue 4- Black Yellow NC

Hello,
Here is the wire diagram for several common mics in relation to a 4 pin CB. Most recent 4 pin CB's such as Midland, Cobra, Connex, Uniden, etc can use 4 pin mics. The wiring is actually depending on the mic rather than the CB so long as the CB's are 4 pin as well. Once you go back to late 80's the 4 pin design was a little different. Anything new it is simpler.
Stock Mic 1- Shield (Ground) 2- Yellow (Audio) 3- Red (Transmit) 4- White (Receive)
Astatic - 4 wire 1- Shield 2- White 3- Red 4- Black
static - 6 wire 1- Shield & Blue 2- White 3- Red 4- Black Yellow NC

Daiwa EM-500 Cobra CA Series 1- Shield & Black 2- Red 3- White 4- Blue
Galaxy DC-521S - 4 wire 1- Shield 2- Yellow 3- Red 4- Black
Galaxy CB-660EI 1- Shield & Black 2- White 3- Red 4- Blue
Sadelta 1- Shield 2- White 3- Brown 4- Green
Turner RK56 Road King 1- Shield & Red 2- White 3- Blue 4- Black Yellow NC
Regards, Tony

1 - Red
2 - Green
3 - Blue
4 - NC
5 - DDC Return
6 - GND (R)
7 - GND (G)
8 - GND (B)
9 - NC
10 - GND-Sync/Self raster
11 - NC
12 - DDC Data
13 - H-Sync
14 - V-Sync
15 - DDC Clock

The wire colours in the actual cable are:

Red (foil wrapped with 1 bare ground wire)
Green (foil wrapped with 1 bare ground wire)
Blue (foil wrapped with 1 bare ground wire)
Transparent (foil wrapped with 1 bare ground wire) All the above go to the corresponding Gun Color, the Bare wire goes the one GND pin.
Purple
Yellow
Black
Orange
White
Bare braided outer ground wire. Combine ALL earths to a single point.
You will have to open up the unit, to see what colors are used for the 5 - DDC Return 10 - GND-Sync/Self raster 12 - DDC Data
13 - H-Sync
14 - V-Sync
15 - DDC Clock
Settings they are marked on the motherboard.

here is the info you asked for the following is the correct wiring.


Mic Wiring Info
Stock Mic Wiring
1. Ground Shield
2. Audio Yellow
3. Transmit Red
4. Receive Black
5. CH. Up White
6. CH. Down Blue
Turner 4-Wire MIC. Wiring
1. Ground Shield
2. Audio White
3. Transmit Black
4. Receive N/C
5. CH. UP N/C
6. CH. Down N/C

Turner 6-Wire MIC. Wiring
1. Ground Shield & Red
2. Audio White
3. Transmit Blue
4. Receive N/C
5. CH. UP N/C
6. CH. Down N/C

Astatic 4-Wire MIC. Wiring
1. Ground Shield
2. Audio White
3. Transmit Red
4. Receive N/C
5. CH. UP N/C
6. CH. Down N/C

Astatic 6-Wire MIC. Wiring
1. Ground Shield & Blue
2. Audio White
3. Transmit Red
4. Receive N/C
5. CH. UP N/C
6. CH. Down N/C

Pin 1 is shield, thats the bare wire wrapped around the mic audio wire
pin 2 ic mic audio [usually white)
pin 3 is transmit or push to talk usually red
pin 4 is recieve or speaker complete usually black

I opened up one of my Cobra HighGear mics and here is how it is wired:

1. shield (Bare copper wires) --- twist them good and tin with a little solder

2. audio (White)

3. transmit (tx) (Red)

4. receive (rx) (Black)

Blue and Yellow are unused.


Dean
Rollin CBs

Pin 1 is Shield(most mics this wire is bare copper) Pin 2 is Audio wire(most mics this wire is white) Pin 3 is Transmit(most mics this wire is red) Pin 4 is receive(most mics this wire is black)