Have a 6000 series and speed control is not working , cannot increase or decrease chair speed ,jot

Probably not. You need a programmer (a PP1) that will allow you to increase the factory speed. But it's probably set at 100% already. Other than setting the speed on the joystick to full and changing the programmed speed will you be able to get the chair 's speed increased.

You need a programmer (a PP1) that will allow uo to increase the factory speed. But it's probably set at 100% already. Other than setting the speed on the joystick to full and changing the programmed speed will you be able to get the chair 's speed increased

You need a programmer (a PP1) that will allow you to increase the factory speed. But it's probably set at 100% already. Other than setting the speed on the joystick to full and changing the programmed speed will you be able to get the chair 's speed increased.

quantum 600 wheelchair troubleshooting Questions ... - Fixya

www.fixya.com > Forum > Tags

quantum 600 wheelchair troubleshooting chair won't go all i get form joystick is a picture of a ... around in a square there should be a rest button on the rear of the chair ,push ... Question about 600 E Electric Wheelchair - Used Power Chair.

[PDF]Pride Quantum 600 Owners's Manual - Scootaround

www.scootaround.com/.../Pride%20Quantum%20600%20Owner's%20M...

Quantum 600 .... The symbols below are used on the power chair to identify warnings, mandatory actions ... Pride will not be held responsible for injuries and/or property ...complete stop by releasing the joystick, then push the joystick forward slightly to .....breaker button, turn on the controller, and continue normal operation.

[PDF]Quantum 600E Owners Manual - Scootaround

www.scootaround.com/.../Pride%20Quantum%20600E%20Owner's%20...

Quantum 600E .... The symbols below are used on the power chair to identify warnings, mandatory ... chair. Pride will not be held responsible for injuries and/or property ... complete stop by releasing the joystick, then push the joystick forward slightly to ..... breaker button, turn on the controller, and continue normal operation.

[PDF]Quantum 600 Series - Pride Mobility Products

I take it you are talking about increasing the maximum speed beyond the maximum the chair is set for now! the max listed speed for the jet 3 is 4mps, so if your chair is doing that there is only changing a load of hardware to increase speed past that (it is very costly) if your chair is second hand it may be that the chairs programming has been changed to reduce the max speed say for in-door use or for elderly with slow reactions to better control the chair, if that is the case it depends on the controller you have it would need a programmer box, you can buy these on ebay and the like or you could take it to a mobility shop and see if they will change it, a lot of these shops will offer to do it free to try and get your future custom, it only takes a couple of mins, most will just plug in to the charge / data port on the controller, select from the menu and adjust the speed etc. hope that helps.

You may have a thermal rollback issue. Try charging the chair overnight and leave the controller on while charging. This will give the control module/joystick time to reset themselves. Thermal rollback happens when a certain temperature in the motors is reached. The system shuts itself down to protect from damage.

Great question! The slow flash is indicative of a speed reduced mode on models designed for a seat lift option. If the controller detects that the seat is elevated then the speed is reduced - regardless of what you try to do at the joystick.
First - try lowering the seat to its lowest position.
If this doesnt work then look for a bad or disconnected sensor switch on the seat post. There are two leads at a 2-pin plug that are not making a connection when the seat is lowered - causing the controller to sense the chair is not safe to drive fast.

Do all of the speed lights flash at the same time or do they ripple from left to right? If they ripple from left to right the chair is in lock mode and you can use the unlock procedures from my tips to unlock. If they are all flashing at the same time you have an internal joystick problem and the joystick needs to be replaced Hope this helps

Try This:

To unlock the power chair.
1. Use the on / off button to switch the control system on. The maximum speed / profile indicator will be rippling up and down.

2. Deflect the joystick forward until the control system beeps.

3. Deflect the joystick in reverse until the control system beeps.

4. Release the joystick, there will be a long beep.

5. The power chair should now be unlocked.

Hope it works.

It could be that the acceleration is set to low. This setting adjusts the time it takes for the chair to reach maximum speed that you have selected on the joystick. With a low setting, it takes it a few seconds to get to maximum. Reprogramming the acceleration to a higher setting decreases the amount of time for the chair to hit max speed. You will need a PP1 handheld programmer from P&G drives technology to change the settings, or take it to a local DME specialist who will usually have a programmer to reset the joystick.