How do I sync in my handset to the base - Uniden Cordless Phone

In the instructions you need to find how you Sync the base and add that number phone to the base. All have different ways so try the company website on google.

Unplug power cord from the base for ten or fifteen minutes, this is the only user level operation that you can do to try fixing the problem.

If after resetting the base still do not find the handset, then either the base or the handset is faulty.

If the base works fine with a different handset, then it is the handset.

335 is the magic code when you want to remove a previous handset or base station registration!
Handset:

1 " (middle soft key) i L i #

2 Enter "335".

3 "Cancel Handset" i #

LThe numbers of all handsets

registered to the base unit are

displayed.

4 Select the handset(s) you want to

cancel, by pressing the desired handset

number. i #
5 "Yes" i # i {ih}
Base Station:

A handset can be registered to a maximum

of 4 base units. A handset can cancel a base

unit that it is registered to. This allows the

handset to "forget" the base unit.

1 " (middle soft key) i N i #

2 "Registration" i #

3 Enter "335".

4 "Cancel Base" i #

5 Select the base unit(s) you want to

cancel, by pressing the desired base unit

number. i #
6 "Yes" i # i {ih}

If they (hand-sets) have already been synced to a base...

The preferred way is to UN-sync from their OLD BASE.

The manufacturers are SMART ENOUGH to realize
the bases & remotes may not ALWAYS remain associated.

You must first UN-REGISTER any association with their
PREVIOUS EXISTANCE... before you can register these on your base...

Likewise... you WILL BE A LOT HAPPIER if you
UN-REGISTER the REMOTES you are planning
to retire

The numbers are quoting are wireless (remotes).

DS6222-4 Wireless handset Manual:
Results 1 8 of 8

You should also look at the instructions for
your (wired) BASE.

There are at least two ways for EVERY TASK...
(you only need one (your choice)).

Carnac the Magnificent

If by "sync a handset" you mean register a handset so it works with the base, then yes. It doesn't even need to be the same model. The manual gives instructions for registering a handset to work with the base. If you need a manual, select the model of your Uniden DECT 6.0 phone from the list beginning at http://www.uniden.com/owners-manuals/dect-phones/scat/dectphones_mnl .

Check your user's manual for registration, or RE-REGISTER the handset to the base. In essence, it involves stepping to the registration on the handset, pushing the handset locator button on the base, then saying OK on the handset. They will sync up.

Carl

have the main based plugged into a working ac outlet and active telephone line then place phone on base for 1 minute then remove base should sync within that time

Hi.


Try the following procedure to reset and re-sync the phone system:

• Disconnect all units from power.
• Remove batteries from all handset.
• Check all phone connections to base.
• Check the phone connector underneath the base (RJ11 squared plug).
• Put back battries on handsets.
• Place handsets on base.
• Connect base back to power with handset sitting on base.

If that does not fix the problem , then there is an internal fault. In that case call Uniden to arrange repair or replacement.

Uniden support number for your area is prited inside the user documentation.


Regards.

Pull battery out of handset for 5 minutes and replace. Then, sit each handset into base cradle until the unit(s) sync.

This works on MY panasonic; May work on yours too!

Registering a handset
The included handset and base unit are
preregistered. If for some reason the
handset is not registered to the base
unit, register the handset.
1 Handset:
{MENU} i {0}{0}{1}
2 Base unit:
Press and hold {LOCATOR/
INTERCOM} until the IN USE
indicator flashes.
LAfter the IN USE indicator starts
flashing, the rest of the procedure
must be completed within 1
minute.
3 Handset:
Press {OK}, then wait until a beep
sounds.
4 {OFF}
Registering an additional handset
See page 5 for information on the
available model.
Start from step 2.