Maytag Bravos Quiet Series 400: F01 Error code

OL = Overloaded.

Is the Washer overloaded? If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent.Feb 24, 2020

OL - Error Code - Top Load Washer - Product Help - Maytag

Maytag https://producthelp.maytag.com > ... > OL

The washer has ol on it at the end - Maytag Bravos quiet ...

iFixit https://www.ifixit.com > Answers > View > The+washe...
Oct 6, 2014 · 2 answers
First, OL stands for "Overload", so in other words, the washer thinks the tub is too hard to move because it's overloaded and the motor is ...
OL code all the time even with very small and light ...
2 answers
Sep 28, 2016
Why washer stops and gives code "ol" - iFixit
2 answers
Nov 30, 2016
at the end it says OL - Maytag Bravos quiet series 300 ...
1 answer
Dec 29, 2022
OL code showing . - Kenmore 110 Series Washing ...
2 answers
Sep 19, 2017
More results from www.ifixit.com

Try unplugging the dryer (or switching your circuit breaker to off). Wait at least one minute before restoring the power. Sometimes leaving the dryer unplugged for 5 minutes is better if a power surge hit the control board.

If the error recurs immediately, then the problem is a bad control board. Otherwise, try to start a dryer cycle and check if the error recurs. If it does, you have a problem with the main control board for the dryer or the wiring connected to the control board.

Please add a comment with the model number of the dryer if you would like me to find the parts list and pricing.

I hope this helps.

Cindy Wells

not good :>(

F01 means that the main relay control board inside your control panel has failed and your control board would need to be replaced to fix the issue.
Apr. 18, 2014

Maytag Bravos Dryer has F01 diagnostic code flashing and ...

https://www.youtube.com/watch?v=xpTCLMugh60
https://producthelp.maytag.com/Laundry/Washers/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers

From the Maytag site: To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

F-01 Means the main electronic control board is likely to have failed.

Unplug the dryer for 5 minutes and the plug the dryer back in. If the code reappears, replace the main electronic control board.

This is where I would start.

Maytag Dryer Circuit Board Timer Parts

Maytag Bravos 7.0 Cu. Ft. Electric Dryer F73 - Questions ...

www.fixya.com/search/p688923-maytag_bravos_7_0_cu_ft.../f73
have a bravo dryer , wont start shows error code f73 ? lights come on but dryer ... I think there was an F73 or F93 error message but we did not write it down.

You need to replace the lid switch. Here is a link to the part.

Most likely the drain pump under machine.

F01 - There may be an internal problem with the control, attempt a Hard Reset.

Hard Reset - In some cases the control can be non-functioning or may not accept activation from the control panel. To clear and restart the control follow the these steps:

* Unplug or turn the circuit breaker off for 30 seconds.
* Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.
* Press the Pause/Cancel/Stop button twice to clear the "PF" in the display.
* Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts.

The F01 generally indicates a failed electronic machine control board.
This error code can sometimes be caused by a glitch or power surge through the electrical lines.
You may be able to clear this code by unplugging the washer for 5 minutes.
If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.

The procedure for accessing and replacing this control board is shown in this image...

http://media.fotki.com/1_p,wkwdftgtbkdgfrwxgtqsskgwtqkq,vi/ksrttqdqrxkssrqtgsd/1/1303472/5961857/image12917img-or.jpg

Be sure to unplug the washer before accessing internal components.
When you access the control board, I recommend transferring the wires from the old control board to the new replacement control board one connection at a time.
Once you have all of the wires transferred, remove the old control board and mount the new control board in the washer.
Reassemble and test the washer.

The "F01" error code indicates a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU.
The "F01" can also be displayed if the onboard "Pump Driver" fails to activate.
Generally in order to correct this failure will require replacing the CCU.
There is no way to test and verify if the control board has failed.
The technical data sheet basically states to replace the CCU.

http://media.fotki.com/1_p,wkwdffkrdwtbgwsxgtqsskgwtqkq,vi/ksskgsfwrxksrttqdqr/1/1303472/5961857/image12923img-or.gif


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question