Question about Electronics - Others

1 Answer

PG156R diode equalent - Electronics - Others

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,390 Answers

Hello Shakeel, the PG156R diode, you can replace it with any fast diode of 1000 Volts, 3 Amper
I send you a link for you to unload the PG156R datasheet and another about the replacement
I hope you can solve the problem
Greetings Franco Dosil

Hola Shakeel, el diodo PG156R, lo puedes reemplazar por cualquier diodo rapido de 1000 Volts, 3 Amper
te envio un link para que descargues el datasheet de PG156R y otro sobre el reemplazo
Espero puedas solucionar el problema
Saludos Franco Dosil PG156R NTE Equivalent NTE571 1000V 3A soft recover

Posted on May 28, 2019


1 Suggested Answer

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I know vhf pretty well. But cbs uhhhh. I have a cobra 29ltd classic. My. Buddy blew diode. Wired backwards. I replaced diode. Now it's making a constant humm from speaker. The swr meter stopped.

did you replace it with one that is equal to the one that burnt .The one you replaced should have been the reverse polarity diode which should have been right near the smaller transformer .If this is the radio it looks like you should replace some of those electriclytic caps also.Did you replace the diode with the arrow pointing in the direction the arrow is pointing ?

Apr 28, 2016 | Cobra Radio Communications

1 Answer

What caused my board to short out, and stop working. Lights just blink, and both fans on the back stop working...

the reason it is doing this is there is a fault on the output board, and it is going into protect mode. check the usual suspects, output transistors, driver diodes, and bias resistors. if none of the easy to replace components are shot, replace the circuit board, as this board is surface mount, there is very little hope of repairing it cheaper then replacing the whole thing. sorry

Mar 07, 2015 | Behringer Pmp6000 Powered Mixer 1600w 1600...

1 Answer

Ic burned

which ic burnt? if in the output (amplifier) stage it is probably a transistor (or pair) that went out. you will also need to replace the biasing resistor and diode. if in the input/preamp stage any general purpose 8 pin op-amp will work. Be careful when soldering this unit, it has a multi level circuit board. If this unit is out of warranty (over 2 years old) It will probably be more economical to purchase another unit imo. good luck.

Mar 22, 2014 | Behringer Pmp6000 Powered Mixer 1600w 1600...

1 Answer

Not heating

There are usually three reasons for this, the magnetron is bad "common problem" or the high voltage capacitor and diode developed a flaw. Depending on the nature of the repair, the cost for parts and labor may equal the price of a new microwave oven.

Mar 06, 2011 | Emerson Black Microwave Oven

1 Answer

Which kind of diode is ph c20?

It is a 20V; 500mv zener diode. Equalent is BZX-C20. OK.

Feb 21, 2011 | Televison & Video

Not finding what you are looking for?
Electronics - Others Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electronics - Others Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers


Level 3 Expert

85160 Answers

Brad Brown

Level 3 Expert

18072 Answers

Are you an Electronics - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides