Hisense LED TV remote not working - Press any button on the remote & it mutes the tv, the standby light flashes red & blue. The manual buttons on tv still work.

Try following the steps below.
Step 1
Press the power button once. If the TV does not turn on, observe the LED indicator, usually located on the TV's lower front panel. If the LED indicator turned off after you pressed the power button once, it is in standby mode. Press the power button once again to exit standby and turn on the TV.

Step 2
Observe the Standby light if the remote control will not work. If the Standby light stays on, the television is in Standby mode. Press the power button on the television, then try to use the remote.

Step 3
Turn the Energy Saving Switch off, then press the power button. The Energy Saving Switch is located on the rear or side panel on most Sony model TVs. Refer to your TV user manual for the exact location of the switch.

Try an auto search with the remote, you might have already tried it :

1. press tv

2. press select and the red button simultaneously untill the LED light flashes twice

3. Then keep pressing the TV and Standby buttons one after the other (not at same time) until the tv swithches off, then press select to store the code, the LED should flash twice to confirm this.


Once you have the remote working the TV, you can get the remote blink back the TV code so you can write it down for future reference.

• Press the TV button on the Sky remote
• Hold down Select and the Red buttons together for approximately two seconds until the LED blinks twice
• Key in 9, 9, 0
• Key in 1 on the numeric keypad and count the number of times the Red LED blinks. This is the 1st digit.
• Repeat for 2 and 3
• Note: no Blink = 0 (zero)

Try an auto search with the remote, you might have already tried it :

1. press tv

2. press select and the red button simultaneously untill the LED light flashes twice

3. Then keep pressing the TV and Standby buttons one after the other (not at same time) until the tv swithches off, then press select to store the code, the LED should flash twice to confirm this.


Once you have the remote working the TV, you can get the remote blink back the TV code so you can write it down for future reference.

• Press the TV button on the Sky remote
• Hold down Select and the Red buttons together for approximately two seconds until the LED blinks twice
• Key in 9, 9, 0
• Key in 1 on the numeric keypad and count the number of times the Red LED blinks. This is the 1st digit.
• Repeat for 2 and 3
• Note: no Blink = 0 (zero)

lrsnihe

You were attempting to perform a power scan initially. The second procedure is manually attempting to address the remote to your TV. I will give you the procedures again so you can try one more time. Emerson TV is one brand we have a low percentage of success getting our remotes to work. If it still doesn't work, we could try replacing the remote.

TV code: 623, 667, 666, 233, 516, 537, 544, 642, 655, 699, 000, 999, 888, and 720.

Remotes: Basic (Television Only)

1. Turn the Television On.
2. Press and hold the clear TV button for six seconds until the LED flashes.
3. Enter the three-digit code using the buttons on the number pad.
4. Press #. Note: The LED will flash three times.
5. Test functionality with the TV.
6. Return to Step 2 if the remote is not able to turn the TV On/Off, change the volume and mute the television.

Remote Power Scan: Basic Remote (Television Only)

1. Turn the Television On.
2. Press and hold the clear TV button for six seconds until the LED flashes.
3. Press and release the red TV Power button.
4. Press and release the Up or Down Arrow on the remote until the television turns off once every second.
5. After the television turns off, press and release the # button.
6. Test functionality with the TV.
7. Return to Step 2 if the remote is not able to turn the TV On/Off, change the volume and mute the television.

Try this...Press tv on the sky r/c.

Then hold the select and red button at the same time,the red light should flash twice.

Then enter the code 1340,the red light should flash twice.

The press the standby button on the sky r/c,the tv should turn off,if it does then press select button on the r/c to store settings.

Hope this will work for you.

You can find the remote control codes for different brands of devices from
http://www.hifi-remote.com/ofa/codes-tv.shtml#tv

If none of the codes work then we have two other solutions:

1. Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment ,or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.
If you don't find a code that works, the remote will flash four times when you reach the end of all the codes for this device type.

1. PRESS the button for the device you want to program, (TV, VCR, CABLE, etc.), then RELEASE.
2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
3. ENTER 9-9-1 (two blinks on the remote)
4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. (On VCR, LD, and CD players use PLAY instead of POWER)
   Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

2. Learn the buttons from the original

Line up your original remote and the head-to-head before completing the following steps.

1. PRESS and HOLD the SETUP button until the red LED flashes twice.
2. PRESS 9 - 7 - 5, the red LED will flash twice.
3. PRESS the DEVICE key where you wish to learn the function. The next 3 steps must be completed within 10 seconds.
4. PRESS the button that will receive the learned function, the LED will flash rapidly.
5. PRESS the button on the original remote to be learned.

Now you can repeat steps 3 through 5 to learn other functions onto other keys or press and hold SETUP until the Cinema's red light flashes twice to lock in your new feature. (If the red light does not blink twice, stop and repeat steps through 6).
To test the new feature, press and release the device key in which the new feature was learned followed by the key on which the feature was learned

More help for programming your remote can be found here:
http://www.hifi-remote.com/manuals/ofa-l.shtml?URC-7800#device

Hope that helps!

The following steps should be able to correct the problem:
1) Unplug the TV or remove AC power from the TV
2) Count to ten and then plug in the TV
3) Locate the [Menu], [VOL-] and [Power] button on the TV’s side panel
4) Using the buttons on the TV’s Side Panel, press and hold both the [Menu] and [VOL-] buttons.
5) While holding those buttons, press and release the [Power] button one time and count to 3 before releasing the [Menu] and [VOL-] buttons.
6) The TV’s lower left Blue Power LED will come ON.
7) Wait 30 seconds. Confirm that the blue LED on the Lower Left of the TV (not the iPod dock for iPod models) has remained ON during this time.
8) Press the [Mute] button on the TV remote twice
9) Unplug the TV or remove AC power
10) Count to ten and plug the TV in
11) The TV power should automatically come ON and the blue power LED with be ON
12) Wait 40 seconds and the TV picture should appear
13) You can now continue using your TV.
14) If the picture does not appear, power on the TV manually:
· If the LED begins flashing, unplug and power ON a second time.
· If the LED begins flashing again, power ON the TV without unplugging
If the LED begins flashing again, contact us directly by phone to obtain a local authorized service center for you.
If the TV does power on, please reply back with the software version number for us to research this issue. Please follow these steps to obtain the software version number:

1) Press the [Menu] button on the remote control.
2) Using the arrow keys in the center of the remote, scroll over to the "settings" menu and select the [OK] button on the remote
3) Scroll down to "system info" and select [OK] button on the remote

Just got an LG 42LH2000 and code 0206 works

You can find the remote control codes for different brands of devices from
http://www.hifi-remote.com/ofa/codes-tv.shtml#tv

If none of the codes work then we have two other solutions:

1. Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment ,or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.
If you don't find a code that works, the remote will flash four times when you reach the end of all the codes for this device type.

1. PRESS the button for the device you want to program, (TV, VCR, CABLE, etc.), then RELEASE.
2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
3. ENTER 9-9-1 (two blinks on the remote)
4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. (On VCR, LD, and CD players use PLAY instead of POWER)
   Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

2. Learn the buttons from the original

Line up your original remote and the head-to-head before completing the following steps.

1. PRESS and HOLD the SETUP button until the red LED flashes twice.
2. PRESS 9 - 7 - 5, the red LED will flash twice.
3. PRESS the DEVICE key where you wish to learn the function. The next 3 steps must be completed within 10 seconds.
4. PRESS the button that will receive the learned function, the LED will flash rapidly.
5. PRESS the button on the original remote to be learned.

Now you can repeat steps 3 through 5 to learn other functions onto other keys or press and hold SETUP until the Cinema's red light flashes twice to lock in your new feature. (If the red light does not blink twice, stop and repeat steps through 6).
To test the new feature, press and release the device key in which the new feature was learned followed by the key on which the feature was learned

More help for programming your remote can be found here:
http://www.hifi-remote.com/manuals/ofa-l.shtml?URC-7800#device

Hope that helps!

If your issue is not resolved, please do not assign a rating just yet. Please post back as to what steps you took, results, etc, and I will try to assist you further as best I can. I am here at your service.

P.S. - You can rate a solution with one of four ratings as explained under (remember that at times a bit of to and fro dialogue may be necessary to resolve an issue).

• "FixYa!" - The solution provides great advice on how to solve the problem.
• "Helpful" - The solution provides useful leads that helps solve the problem.
• "Thanks for Trying" - The solution does not solve the problem but the effort is appreciated.
• "Inappropriate" - The solution has absolutely nothing to do with the problem.

Thank you for using FIXYA!

IrishDruid