How do i set vibration on alarm on expediton watch

If your Timex Expedition watch alarm and beep function are not working properly, even with a new battery, it could be caused by a few different things. Here are some steps you can try to troubleshoot the issue:

1. Check the alarm settings: Make sure the alarm is turned on and set to the correct time. Also, check that the alarm is set to the correct mode, such as daily or weekly.
2. Check the watch's manual: Refer to the instruction manual that came with your watch to see if there are any specific instructions for setting the alarm or beep function.
3. Check the vibration function: If the vibration function of the watch is not working, it could cause the alarm and beep to not function properly. Try resetting the watch or contacting Timex for assistance.
4. Check for physical damage: Inspect the watch for any physical damage such as a cracked or broken case, or a damaged alarm switch.
5. Check for water damage: If the watch has been exposed to water, it could cause damage to the electronic components. If water has entered the watch, it is best to take it to a professional watch repair center for service.
6. Check if the watch have a warranty: If the watch is still under warranty, you should contact the manufacturer for service or repair.

2 things you could have the back on wrong way or you've lost the small coil spring that touches the back plate of the watch that give you the vibration ,,

Pull out the crown to the alarm setting position. The crown is located on the right side of the face of the watch. Pull the crown out until "AL", the alarm indicator, is shown on the watch. Depending upon the model of your Tag Heuer Aquaracer watch, you will either pull the crown out in the first or second position.

Select the hours and minuets for the alarm. Once your watch is in the alarm setting position, press the bottom right button on your watch. This will enable you to select the hours and minuets that you want to set the alarm for.

Set your alarm. To begin setting your alarm turn the crown clockwise until the desired hour or minutes are displayed on your Tag Heuer Aquaracer watch. If you happen to accidentally pass the alarm time, turn the crown counter-clockwise the get back to the desired alarm time.

Save your alarm. When you are ready to save your alarm, simply push in the crown. Once your alarm sounds, to silence it press any button on your Tag Heuer Aquaracer watch.

Best Deals Casio Women s Vibration Alarm Watch LDF10-7A Get Perfect If you are looking for news and reviews, Casio Women s Vibration Alarm Watch LDF10-7A The Buyer s Guide.

Boluva do not have anything useful on their web site except that you can locate your nearest service center. If you go to "Boluva.com" and find the service center, they should be able to help you.

It can be the battery if your watch model has separate battery for alarm function. If your watch originally is running on one battery, then check out if the sound transmitter spring is missing. Sound is transmitted through the coil spring or small peace of metal which is sticking upwards out of movement, so, when the case back is fitted to the case, the spring is touching sound membrane inside the case back, thus enabling transmit vibrations (sound). If there is nothing as I just described, you will need to get one and fit it to the movement. If there is such a spring, then movement has micro electric fault and should be fixed. In both cases you have to visit your nearest watchmaker and ask for help.
Rate me, plz.

No, there is nothing wrong with the alarm in your watch.
The sound in all watches are generated by passing vibrations to the metal tweeter which is connected to the watch caseback inside the watch. As the surface of the watch is quite small, there is not efficient power to spred the vibrations over the caseback surface, hence low volume of the alarm. No wristwatch in the world is capable of loud alarm sound yet. This is something the scientists have to work with.
The plastic protector is definetly affecting the volume. Take it off and you will notice slightly better sound. This protector actually is ment to protect watch caseback from scratches prior to selling it to the customer and have no use after that. In fact it only collects the dirt and bacteria and can affect your skin as the caseback as well.
Another sound improvement can be the new battery if the original is underpowered. Alarm feature uses the most of the energy stored in battery and the power consumption is higher than all watch movement parts put together.

Rate me, please.

Hold down the "time set" button until the time on the clock flashes. Then use rev or fwd to set the time. Press the "time set" button again once you have the correct time. You can do the same to set the alarm by holding down the "alarm set" button.

the middle dial on the right side of the watch is used to switch from watch settings to alarm settings..
pull the middle dial out to put it in alarm mode.
To set alarm:
-pull the center knob out.
-with it out you can now use the bottom (right) knob to set the alarm.
-pull the bottom right knob out one notch
-turn the knob clockwise or counter clockwise to set the alarm time
-push the knob back in (all the way)

the alarm is now set

if the center (right) knob is pulled out the alarm is ON
if the center (right) knob is pushed in the alarm is OFF
--------------------------------------------------------
I have owned this watch for about 10 years now and love it.
the past few years the chronograph buttons (on the left side of the watch) were not working well rendering the chronograph and count down timer functions unusable.

repairing a chronographs is expensive and watch makers usually charge several hundred dollars which is not a feasible fee for a watch of this value so i decided to open it up my self and clean it up and that did the trick.. its working like new!

enjoy the watch!

Hi Hoffman518,

To set the alarm on your Timex Ironman, please follow the steps below.

1. Begin by pressing the "mode" button until the alarm screen appears.

2. Press the "set" button and use the "advance" button to set the hour for your alarm.

3. Repeat the same procedure to set minutes and seconds for your alarm.

4. When you have finished setting the alarm, press the "set" button, followed by "advance" save and activate your alarm.

5. When you alarm sounds, you can deactivate it by pressing any button on the watch.

Hope it helps.

Thank you for using FixYa.