How do I connect a mixer to my pioneer receiver

See the attached image for a 1/4" TRS balanced output from the mixer Stereo Out to unbalanced input at the receiver (I assume the receiver has RCA connections). You'll need two of these - 1 left and 1 right. Make sure to turn the mixer down, then raise the mixer level gradually, because the mixer's professional output level is a bit higher than the consumer level normally seen at the receiver input.

You can use the RCA jack and an RCA cable to your aux in on your receiver.

you have created a closed loop.... to fix it do this deck output ----> fx unit input -----\ fx output-----> to mixer or power head reciever /input\

If your CD player works hooked up to the DJ board, then try hooking the line out of the board into a auxiliary in or line in in or record in on your receiver using the appropriate cables.Try the CD in first and if there is too much signal then use the CD/Tape in. You need to match the output signal of your board to the input signal of your amp. Hope this helps.

Home-theatre receivers don't have microphone inputs. If you want to use the receiver as an amplifier in PA system, you need to use some kind of mic pre-amp or a mixer with mic inputs.
For PA mixer is needed anyway almost every time and all mixers have at least one mic input (with a pre-amp). Mixers have line-level output(s), which you can connect to the analog input of receiver.
Using receiver as an amp in PA has advantage that you have 5 channel amp. When using high sensitive PA speakers (as oposed to less sensitive Hi-fi home speakers), you can get good performance with the power rating of receiver. You could even use 2 separate channels for subwoofers and 2 channels for satelite speakers - but for that you would need a receiver with 5.1 analog inputs and special device called crossover which would divide the output from mixer into low-frequency signal and high-frequency signal which you would then connect to the front and rear analog inputs. But with RX-V365 you can use only 2 channels with analog input

Had to download the manual for this one since i didn't work with that particular model yet, but should be able to help anyway. Ok so on the back of the Yamaha unit you have a total of 5 HDMI plugs. The first on the left is the receiver's output which is supposed to go to the Pioneer flat screen in the Input HDMI plug. The 4 other HDMI plugs on the yamaha receiver are the 4 inputs, so plug in the Blue Ray reader into the second HDMI plug from the left which reads (BD/DVD) HDMI1. Now everything is plugged in the right way, so if you already did plug it all up like that, you were OK so far. All that is left now is to first of all put the Pioneer flat screen on the right input (You can do that with the remote of the TV, or if i'm not mistaken, there is an input selector on the back of your Pioneer flat screen TV). When that is done you just need to put the receiver to the right input also, to do so, either with the remote again, or on the front of the yamaha receiver unit. In both case, the button you need is the Input button, press it untill the receiver says HDMI 1 on the LCD display. And now you're done, all you need to do is to turn on the Blue Ray, put a movie in and enjoy.:) If it does not work, either the receiver or the flat screen are defective and should be returned for waranty.

Use the stereo master outs from the DJM into the A and B Inputs of the EQ (you'll need 2 phono to Jack or 2 phono to XLR cables) then from the A and B Outputs of the EQ to the power amp/ speakers, etc (you'll need jack or XLR cables depending on what is powereing your speakers)

check your input (cables and device)for bad or short circuit cable-bad plug--connection between inner conductor and shield. of the cable(test with new one)------you can disconnect inputs one by one until you find the bad one.and change it.

depends what audio outputs you have on the sky box,analogue (two phono usually red for right channel and white left channel)in which case just use phono leads to the phono inputs,Optical(toslink),connect an optical cable from the output to the optical input on the dvd channel of the pioneer,coaxial (spdif)connect to spdif input on the laser disk input of the pioneer,dont connect to the attenuated spdif.In the unlikeley event of the sky box not having any audio outputs,just use the outputs from the tv to the pioneer.The optical digital input gives the best quality on the vsa eo6

No phono inputs?? You will need a phono to line level preamp to use aux input.