The clock display flickers (digital) constantly and you can't tell what the clock or the timer is set too.

RANGE SETTING THE CLOCK NON-ELECTRONIC CLOCKS: To set the clock:

1. Push the center knob in.
2. Turn the clock hands to the correct time. If the Minute Timer pointer should also move, let the knob out, and turn the Timer pointer to OFF.

DIGITAL CLOCKS: To set the clock:

1. Push in the center knob of the Minute Timer.
2. Turn knob in either direction to set the Digital Clock numerals to the correct time

ELECTRONIC CLOCKS: To set the clock (models with Clock or Set Clock pad):

1. Press the Clock pad
2. Press the + / - pads or number pads (depending on model) to set the time.
3. Touch the Start pad. The time of day will show in the display.

To set the clock (models without Clock or Set Clock pad):

1. Press and hold the + and - pads for 3 seconds.
2. Press the + / - pads to set the time.
3. Touch the Start pad. The time of day will show in the display.

Range Setting the Clock and Timer Non-Electronic Clocks: To set the clock, push the center knob in and turn the clock hands to the correct time. (If the Minute Timer pointer should move also, let the knob out, turn the Timer pointer to OFF.)
Digital Clocks: To set the clock, push in the center knob of the Minute Timer and turn Knob in either direction to set the Digital Clock numerals to the correct time.
Electronic Clocks: To set the clock touch the Clock pad. Touch the number pads. Touch the number pads. Touch the start pad until the time of day shows in the display. Note: On double wall ovens, you can only set the Timer for one oven.

Hi Jason. Have you performed the following actions?
Electronic Timing Center (Analog Clock w/Digital Display)
Synchronizing the analog and digital clocks
1. Press the "timer" and "start time" buttons simultaneously.
2. Turn the set knob to move the hands on the analog clock to any time setting.
3. After five seconds the display will go blank. Press the timer button and using the set knob, set the digital time to the exact time on the analog clock. This will synchronize the two clocks. You can now set the time of day.
Setting the Time-of-Day
The time-of-day must be set before any other program can be used. When your oven is first connected to the power in your home, the digital display will show 00:00. To program the time-of-day:
1. Push and hold the "timer" and "bake hours" button at the same time.
2. Turn the "Set" knob until correct time is displayed on the digital clock.
3. Release "timer" and "bake hours" button
The analog clock will automatically set after the digital time is set

Let me know so that I may follow up if need be.

The Display is shorting out, bad news is it is part of the ERC (Electronic Range Control) Pricy to replace, go to marcone.com with your model Number and you can order the part, not hard to replace

Hello
To set clock:
1. Press "Timer/clock button". The hour digit begins to flash.
2. Press (<< P.DOWN or >> P.UP) on the multicontrol to set Hours.
3. Press SET button. The minute digits begins to flash.
4. Press (<, P.DOWN or >> P.UP) on the multicontrol to set Minutes.
5. Press "Set" button."CLOCK OK" appears on the display. The clock stops flashing, and the clock timer starts from "0" seconds. If the clock is not set "AM 12:00" will flash instead of the clock indication. When the time has been set, TIMER/CLOCK can be used to operate the daily timer recording timer.
If you haven't the user manaul to your set with you now, send your email address to me by Fixya comment bos. I've the downloaded user manual to your set, and I'll send a copy of it to you by return mail. OK.

There are lots of different timers on fisher and paykal The last one I reset was a few weeks ago it involves pressing 2 buttons at the same time I think it was the oven on and oven off buttons but I am not sure You will know when you have pressed the right 2 buttons the display will stop flickering set the clock time using the up down arrow buttons The auto light should not be on if it is press the manual button Regards Geoff Stove Recyclers

I recently bought one. The instructions are on the packaging.

To switch from timer mode to clock mode, press STOP and START together.

To set the clock, press START and hold for 5 seconds until the whole display flashes. Press HOUR to set the hour. Press MINUTE to set the minutes. Press START to start the clock.

To set the clock go to the link below page 9 will tell you how to set clock.


http://resources.jvc.com/Resources/00/00/97/MB002ien.pdf


On the remote control ONLY:

1 Press CLOCK/TIMER.

The hour digits start flashing on the display.

2 Press UP or DOWN to adjust

the hour, then press CLOCK/

TIMER.

The minute digits start flashing.

• When you press and hold UP or

DOWN, the hour digit changes

continuously.

3 Press UP or DOWN to adjust the

minute, then press CLOCK/TIMER.

The built-in clock starts.

• When you unplug the power cord or if a power failure occurs

The clock is reset to "AM 12:00" right away. If this happens, set

the clock again.

• The clock may gain or lose 1 to 2 minutes per month
If this happens, reset the clock.

Woods 59301
Manual for 59301
http://waterheatertimer.org/pdf/Woods-59203.pdf

Plug timer in wall for 1-2 hours so rechargeable battery charges
If display does not show after 1-2 hours, the battery is dead and timer is no good

After 1-2 hours, you can remove timer from wall to program

Press reset (R) with paper clip to clear memory

Select format: Press and hold Clock button until 12 hour or 24 hour shows on display, then release
Press hour button to change display to 12H
press Clock button and display returns to normal
AM shows in upper left corner

Set current time:
Press and HOLD clock button
While holding clock button, press hour button and minute button until display shows current time
Release clock button
Press and HOLD days button until current day shows in display
Release days button

Further instructions to set ON-OFF times are in manual (click link shown above for manual)
If you have problems, re-post additional question.

I did the following to set the clock:

1. Press the Timer/Clock button until "CLOCK" shows, blinking, on the display.
2. Press Set/Demo. The hour indicator on the clock should start blinking.
3. Use the "Track/Tuner Forward" and "Track/Tune Backward" keys to
set the hour.
4. Press Set/Demo. The minute indicator on the clock should start blinking.
5. Use the "Track/Tuner Forward" and "Track/Tune Backward" keys to
set the minute.
6. Press Set/Demo twice. (Pressing once moves to the timer set mode.)